Replacing a developer unit, 124 | Konftel G510-7276-00 instruction

6Close the top door.

Replacing a developer unit

Replace a developer unit when a print quality defect occurs or when damage occurs to the printer.

Note: When a developer unit is replaced, you must manually calibrate the color. For more information, see “Color misregistration” on page 149.

1Grasp the front door at the side handholds, and then pull it toward you to open it.

CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot component, allow the surface to cool before touching.

2Open the top door.

Maintaining the printer

124

Image 126

Konftel G510-7276-00 manual Replacing a developer unit, 124

Contents

InfoPrint Color 1824 MT4985 Page InfoPrint Color 1824 MT4985 Contents Clearing jams Understanding printer messages 107 131134 154 137 161 Page Safety info rm ation Page Printer configurations Learnin g about the printerBasic model Fully configured model Selecting a location for the printer 304.8 mm 12.0 in mm 20.0 Understanding the printer control panel Description Available options Installing internal optionsAdd itional p rinter se t up Memory cards Accessing the system board to install internal options Flash memory card connector Memory card connector Installing a memory card Notch Latch Installing a flash memory card Plastic pins Metal pins Installing hardware options Installing a 650-sheet duo drawer Attaching cables Verifying printer setup Printing menu settings pages Installing printer software Setting up the printer softwarePrinting a network setup For Windows users Updating available options in the printer driver Windows Setting up wireless printing Installing the printer on a wireless network Windows Click Suggested Click Wireless Network Attach Installing the printer on a wireless network Macintosh Prepare to configure the printerEnter the printer information Configure the printer for wireless access Configure your computer to use the printer wirelessly Installing the printer on a wired network Choose the Default Browser tab Click More Printers Windows Vista Double-clickPrint Center or Printer Setup Utility Linking trays Load in g pape r a nd s p ecialty mediaLinking and unlinking trays Unlinking trays Setting the Paper Size and Paper Type Configuring Universal paper settingsSpecify a unit of measurement Loading the standard 250-sheet tray Specify the paper height and widthPage Loading the optional 650-sheet duo drawer Using the multipurpose feeder Tab Stack height limiter Using the manual feeder For Windows usersFor Macintosh users Page Paper characteristics Pap er and specialty m e dia g uidePaper guidelines Selecting preprinted forms and letterhead Supported paper sizes, types, and weights Storing paperPaper sizes supported by the printer Paper types supported by the printer Paper types and weights supported by the printer Standard 250-sheet Optional 550-sheet Tray Tray Paper capacities Input capacitiesOutput capacity Using recycled paper and other office papers Prin ting Printing a document Tips on using letterhead Printing specialty documents Tips on using transparencies Tips on using envelopesPage Tips on using card stock Printing from a flash drive Printing a font sample list Canceling a print job from the printer control panelPrinting information pages Printing a directory list Canceling a print job from the computer Click Control Panel Click Hardware and Sound Click PrintersPage Paper tray recommendations Clearing jamsAvoiding jams Paper recommendations Understanding jam numbers and locations Jam number Jam location Paper jam Remove the jammed paper Close the front door Press Page Paper jam Paper jam Und ersta ndin g prin t e r men us Menus list Default Source menu Supplies menuPaper menu Paper Size/Type menu Tray x Type MP Feeder Size Manual Paper Size Paper Texture menu Paper Weight menu Menu items Paper Loading menu Menu item Description Universal Setup menu Custom Types menu Menu Settings Page menu ReportsDevice Statistics menu Print Fonts menu Network Setup Page menuProfile List menu Print Directory menu Asset Report menu Network/PortsPrint Demo menu Active NIC menu Wireless menu USB menu ENA Address ENA Netmask ENA Gateway Settings General Settings menu Run Initial Setup Setup menu Finishing menu Separator Sheets Quality menu RGB Contrast RGB Saturation Color Balance Manual Color Utilities menu PostScript menu PCL Emul menu Symbol Set Tray Renumber Image menu PictBridge menu Flash drive menu List of status and error messages Und ersta nding prin t e r message s Insert Tray Hex TraceImaging Kit Invalid Engine Code Load single sheet feeder with size Power SaverLoad single sheet feeder with custom string Load single sheet feeder with type size Reload printed pages in Tray Programming FlashReady Remote Management Active Waiting Unplug and change modeUnsupported USB hub, please remove Waiting, too many events Short paper Insufficient memory to support Resource Save featureYy Replace Unsupported color Cartridge Insufficient memory to collate job Standard network software error Ppds Font ErrorStandard x software error Defective flash detected Too many trays attached Standard USB port disabledToo many flash options installed Incompatible tray 24x.yy Paper jam area name Yy Replace color CartridgeYy Paper jam area name 104 942.01 940.01941.01 943.01 943.02 106 Conserving supplies Main taining th e prin t erStoring supplies Checking the status of supplies Ordering supplies Replacing supplies 109 110 111 Replacing a black imaging kit 112 113 114 115 116 Replacing a black and color imaging kit 117 118 119 120 121 Replacing a toner cartridge 122 123 Replacing a developer unit 124 125 126 127 128 Cleaning the exterior of the printer 129 Moving the printer to another location Moving the printerBefore moving the printer Shipping the printer Adm inistra tiv e support Restoring the factory default settingsAdjusting Power Saver 131 Configuring supply notifications Using the Embedded Web ServerSetting up e-mail alerts 132 Copying printer settings to other printers 133 Error message about reading USB drive appears Solving basic printer problemsSolving printing problems Troublesho oting Incorrect characters print Job takes longer than expected to printJob prints from the wrong tray or on the wrong paper 135 Unexpected page breaks occur Tray linking does not workLarge jobs do not collate 136 Flash memory card Solving option problemsDrawers 137 Memory card Solving paper feed problemsMultipurpose feeder Paper frequently jams Paper jam message remains after jam is cleared Solving print quality problemsIsolating print quality problems That jammed does not reprint after you clear the jam Blank pages Characters have jagged or uneven edges140 Gray background Clipped imagesDark lines 141 Incorrect margins Light colored line, white line, or incorrectly colored line142 Paper curl Print irregularities143 Print is too dark 144 Print is too light 145 Repeating defects 146 Toner fog or background shading appears on Skewed printSolid color pages Toner rubs off Toner specks Transparency print quality is poor148 Color misregistration Solving color quality problemsUneven print density 149 FAQ about color printing 150 Printed page appears tinted. Can I adjust the color? 151 What are detailed Color Samples and how do I access them? 152 Contacting Customer Support 153 Edition notice 154 Exposure to radio frequency radiation Industry Canada notices155 156 157 Česky Noise emission levels India emissions noticeStatic sensitivity notice Product disposal Laser advisory label Power consumptionLaser notice 159 Power Saver 160 Index Numerics161 162 163 164 Output bin Support FAQ about color printing 150 solving basic printer 165Page Page G510-7276-00