3.5 Changing the Interface Parameters
6 | Press the Z key. One of the following menus is |
| indicated. To change settings for the item, press the |
ENTER key. Use the U or V key to change the value or selection. Configure settings referring to the explanations below.
3.5.4Resolving IP Address
To connect the printer using TCP/IP protocol to a network in which a DHCP server is not present, you must manually set the IP address using the operator panel. The IP address must be unique to the printer and should be obtained from your
>NetWare | > | |||
On |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Range
Set this item to On when you connect to a network using Net- Ware. In submenu (>), frame mode can be selected from Auto, 802.3, Ethernet II, 802.2, and 802.3SNAP.
network administrator.
1 | Activate TCP/IP protocol in the manner described | |||
| above. |
|
| |
|
|
|
|
|
|
| >TCP/IP | > |
|
|
| On |
|
|
|
|
|
|
|
>TCP/IP | > | |||
On |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
>EtherTalk Off
>Network Status Page Off
Set this item to On when you connect to a network using TCP/ IP. Submenu (>) has items including DHCP, IP address, subnet mask address, and gateway address. To resolve IP address for the network card, see 3.5.4 Resolving IP Address below.
EtherTalk must be activated (On) for net- working with Macin- tosh computers.
When the item is set to On, the printer prints out a network status page when it prints the printer sta- tus. See Printing a network interface sta- tus pages on page
2 | Enter the submenu by pressing the Z key. Make sure | ||||||
| that DHCP is set to Off. If not, press the ENTER key, | ||||||
| then press U key to set it Off. Each time you press the | ||||||
| U or V key, the selection changes as shown below. | ||||||
|
|
|
|
|
|
|
|
|
| >>DHCP |
| ||||
|
| Off |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| >>IP Address |
| ||||
|
| 000.000.000.000 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| >>Subnet Mask |
| ||||
|
| 000.000.000.000 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| >>Gateway |
| ||||
|
| 000.000.000.000 |
| ||||
3 |
|
|
|
|
|
|
|
When >>IP Address is displayed, press the | |||||||
| ENTER key. A blinking cursor (_) appears at the last | ||||||
7 | Activate the appropriate protocol that is required to |
| connect the printer to the network. To activate a |
| protocol, let the protocol displayed, press the ENTER |
| key, press the U or V key to change from Off to On, |
| and press the ENTER key. |
8 | Press the MENU key. The display returns to Ready. |
| You can print a network status page to confirm that |
the IP address, subnet mask address, and the gateway address have been properly set. To print a network status page, see Printing a network interface status pages on page
| digit. | |||
|
|
|
|
|
|
| >>IP Address |
| |
4 |
| 000.000.000.000 |
| |
|
|
|
| |
|
|
|
| |
Press the U or V key to increase or decrease, | ||||
| respectively, the value at the blinking cursor. Use the | |||
| Z and Y keys to move the cursor right and left. | |||
5 | When the IP address is entered, press the ENTER | |||
| key. | |||
