9: Monitor Mode

 

 

 

 

 

 

 

 

 

 

 

 

Command

Command Name

Function

 

 

 

 

 

 

 

PI x.x.x.x

Ping

Pings unit with IP address x.x.x.x to check device

 

 

 

 

status.

 

 

 

 

 

 

 

AT

ARP Table

Shows the unit’s ARP table entries.

 

 

 

 

 

 

 

TT

TCP Connection Table

Shows all incoming and outgoing TCP connections.

 

 

 

 

 

 

 

NC

Network Connection

Shows the unit’s current IP address, gateway,

 

 

 

 

subnet mask, and DNS server.

 

 

 

 

 

 

 

RS

Reset

Resets the unit.

 

 

 

 

 

 

 

QU

Quit

Exits diagnostics mode.

 

 

 

 

 

 

 

G0, G1, ....,Ge, Gf

Get configuration from

Gets a memory page of configuration information

 

 

 

memory page

from the device.

 

 

 

 

 

 

 

S0, S1,...,Se, Sf

Set configuration to memory

Sets a memory page of configuration information

 

 

 

page

on the device.

 

 

 

 

 

 

 

GM

Get MAC address

Shows the unit's 6-byte MAC.

 

 

 

 

 

 

 

SS

Set Security record

Sets the Security record without the encryption key

 

 

 

 

and length parameters. The entire record must still

 

 

 

 

be written, but the encryption-specific bytes do not

 

 

 

 

need to be provided (they can be null since they

 

 

 

 

are not overwritten).

 

 

 

 

 

 

 

SA

Scan

Initiates a wireless scan if the wireless interface is

 

 

 

 

enabled. Reports any stations found, including

 

 

 

 

BSSID, SSID, and RSSI. If SA is followed by a

 

 

 

 

string, the string is used to filter SSIDs before

 

 

 

 

reporting. If the BSS does not broadcast its SSID,

 

 

 

 

only the BSSID and RSSI are returned.

 

 

 

 

 

 

 

NS

Network Status

Reports the network interfaces’ statuses. Includes

 

 

 

 

potentially negotiated parameters like speed/duplex

 

 

 

 

for Ethernet or BSSID, encryption, authentication

 

 

 

 

for wireless interfaces.

 

 

 

 

 

 

 

co

Set IP address, host bits,

Example:

 

 

 

gateway , and DNS server

co 192.168.0.10 8 192.168.0.1 10001 192.168.1.10

 

 

 

IP

with

 

 

 

 

 

 

 

 

192.168.0.10 = IP address of the WiBox

 

 

 

 

8 = number of host bits

 

 

 

 

192.168.0.1 = gateway IP address

 

 

 

 

10001 = port number of the WiBox

 

 

 

 

192.168.1.10 = IP address of the DNS Server

 

 

 

 

The WiBox stores the setup and performs a reset.

 

 

 

 

It sends an X before the reset if the command was

 

 

 

 

OK.

 

 

 

 

 

 

 

WS

Wireless Status

Displays wireless module status that includes

 

 

 

 

packets received, transmitted, and dropped.

 

 

 

 

 

 

Responses to some of the commands are given in Intel Hex format.

WiBox® 2100E Device Server User Guide

76

Page 76
Image 76
Lantronix 2100E manual Monitor Mode, G0, G1, ....,Ge, Gf, S0, S1,...,Se, Sf