Heat pump control monitors mode of | Defrost Calibration |
|
| ||
operation through outdoor ambient | Coil sensor (RT21) detects temperature below 35°F {2°C} | ||||
temperature | (RT13), outdoor coil | during either initial power−up, after loss of power or after | |||
temperature (RT21) and compressor | cooling mode, a sacrificial defrost will be used to ensure there | ||||
run−time to determine when a defrost | is a clear coil before attempting calibration. |
|
| ||
cycle is required. |
|
|
|
| |
NOTE |
|
|
|
|
|
be active for defrost calibration to be |
|
|
| ||
achieved. |
|
| Coil sensor |
|
|
|
|
|
|
| |
|
|
| below 35°F {2°C} | NO | No attempt |
100 |
|
|
|
| to calibrate. |
|
|
|
|
| |
DEGREE |
| E47 |
|
|
|
TARGET |
|
| YES |
|
|
100 | *Heat Pump Control (A175) |
|
| ||
|
|
| |||
|
|
|
| ||
| 90 70 50 | Defrost Termination (E47) |
|
|
|
|
|
|
|
| |
90 |
| Pins (Factory Default is 50ºF) |
|
| |
|
| Accumulate compressor run−time while outdoor |
| ||
DEGREE |
|
|
| ||
TARGET |
|
| coil temperature sensor input (RT21) is below |
| |
100 90 70 50 |
| 35°F (2°C) |
|
| |
70 |
|
|
|
|
|
DEGREE |
|
|
|
|
|
TARGET |
|
|
|
| Continue to |
| 100 |
| 30−35 minutes |
| |
|
|
|
| ||
| 90 70 50 |
| NO | accumulate | |
|
| compressor | |||
|
|
|
| ||
|
|
|
| run time. | |
*50 |
|
| run−time |
| |
|
|
|
| ||
DEGREE | 100 |
|
|
|
|
TARGET |
|
|
|
| |
| 90 70 50 |
|
|
|
|
|
|
| YES |
|
|
| Demand Mode | Defrost Mode |
|
| |
|
|
|
| ||
After the initial calibration, the heat pump control | Initiate a defrost and monitor coil | temperature |
| ||
sensor input (RT21) and accumulate defrost time. |
| ||||
disables the defrost mode for 30−34 minutes in |
| ||||
|
|
| |||
order to avoid unnecessary defrosts. Beyond |
|
|
| ||
this timing period, both the ambient (RT13) and |
|
|
| ||
coil (RT21) sensors are continuously moni- |
|
|
| ||
tored. If the coil temperature is below 35°F (2°C) |
|
|
| ||
and the calibration delta is reached or accumu- |
|
|
| ||
lated compressor run−time is more than six (6) |
|
|
| ||
hours, a defrost is to be initiated. |
|
|
| ||
|
|
| How did defrost |
|
|
|
|
| terminate? |
|
|
Coil temperature sensor input (RT21) reached specified de- frost termination temperature as set on heat pump control E47 pins*.
Defrosted for 14 minutes with- out the coil temperature sensor input (RT21) reaching defrost termination temperature as set on heat pump control E47 pins*.
Calibration Attempted
(Unit Running in Heat Mode)
YES Calibration NO
Figure 26. Defrost Calibration Sequence of Operations
Page 34
506586−01 10/10
