Magnetic Separator K58 | Lincoln Electric SVM127-A specification

C-7

ACCESSORIES

Return to Section TOC

Return to Master TOC

MAGNETIC SEPARATOR (K58)

The K58 is a permanent magnet type separator designed to fit the top of the standard fill funnel of the continuous flux feed system.

The purpose of the separator is to remove magnetic materials such as mill scale and any other extraneous magnetic materials which may have been recovered along with the flux to be processed.

It is important to remove these magnetic particles from the flux which is to be reused in the continuous flux feeding system. If the magnetic material is not removed, it will gather around the nozzle of the gun and impede or shut off the flux flow when making rela- tively long welds or when welding continuously. The magnetic particles can also cause porosity in the weld.

Fit the magnetic separator into the funnel or hopper. Pour the flux to be reclaimed into the top pan of the separator. The separator is designed so that the flux flows around three permanent magnets. The magnets remove all magnetic particles. When the magnets become covered with their full load, they automatically stop the flux flow. When the flux flow stops, remove the separator from the funnel or hopper. Turn it over and open the panel that covers the magnets. Remove the magnetic particles by brushing or by using an air blast.

WARNING

WHEN USING COMPRESSED AIR BE CAREFUL TO PROTECT YOURSELF AND OTHERS IN THE AREA FROM FLYING PARTICLES.

NOTE: The magnetic separator is used with all Lincoln mild steel fluxes - 700 Series, 800 Series and 900 Series. Do not use the magnetic separator with any stainless steel, alloy, or hardsurfacing flux except H-535. The magnetic separator removes some of the alloying elements from these fluxes, thus changing their characteristics.

MECHANIZED HAND TRAVEL UNIT (K110)

Carries K114 Squirtgun along the joint at a preset trav- el speed to help the operator make better welds 10 to 25% faster than with manual travel. Speed range is 7- 60 ipm (.18-1.5 m/min). Requires K161 Power Pack.

SQUIRTMOBILE ® (K62)

Self-propelled trackless carriage carries K114 gun on long welds for automatic welder economy without high fixture costs. Requires K161 power pack.

MECHANIZED TRAVEL POWER PACK (K161-CABLE LENGTH)

Includes travel mag-amp circuit required when using either a K62 Squirtmobile or K110 mechanized hand travel unit with a K114 gun. Mounts near power source. Available with 25, 50, 75 or 100’ (7.6, 15.2,

22.9or 30.5 m) power pack to wire feeder leads. Connect to the power source for input power. (Not suit- able for use with the LN-9F.)

GAS SOLENOID KITS

K425 Mounts inside K357 LN-9 model above code 9131.

K437 Mounts outside all other LN-9 models.

POWER EXTENDED WIRE DRIVE (K392)

Permits extending gun and cable up to 80 feet from the K357 LN-9 (code 8180 and higher).

ENCLOSED REEL MOUNTING (K304)

Used with the LN-9SE for welding at a distance from the wire feeder. Includes a door for the wire reel hous- ing and a hand crank. 50 and 60 lb. reels can be used.

EXTENSION ASSEMBLY (K307 or K308)

For LN-9NE or LN-9SE. K307 is a 221⁄2 ft. (6.9 m) extension cable. K308 is 45 ft. (13.7 m). Permits weld- ing up to 60 ft. (18 m) from the wire reel.

FILLET GUIDE (K70)

Attachment simplifies horizontal fillet welding when using the Mechanized Hand Travel Unit (K110).

LINC-FILL ™ GUIDES

A complete line for submerged arc and Innershield available.

Lincoln Electric SVM127-A service manual Magnetic Separator K58, Mechanized Hand Travel Unit K110

Models: SVM127-A