♦TIME DATE ADJUST
Before you start recording, it is necessary to set accurately the present date and time.
Example: Setting the date/time to 10/28/2003 6:30pm
(18:30). (default: “01/01/2003 00:00:00”)
1.Press the SET UP button to display the <SETTINGS> screen.
2.Check that the cursor (>>) is positioned at “TIME DATE/ DISPLAY SETTINGS” and then press the ENTER button.
•The <TIME DATE/DISPLAY SETTINGS> screen appears.
3.Check that the cursor is positioned at “TIME DATE ADJUST” and then press the ENTER button.
•The <TIME DATE ADJUST> screen appears.
<TIME DATE ADJUST> | OFF |
>>DAYLIGHT SAVING | |
DAY | 01 |
MONTH | 01 |
YEAR | 2003 |
TIME | 00:00:00 |
4.Press the JOG 
,
buttons to move the cursor to “DAY” and then press the ENTER button.
•The background of the setting item turns red and flashes.
<TIME DATE ADJUST> | OFF |
DAYLIGHT SAVING | |
>>DAY | 01 |
MONTH | 01 |
YEAR | 2003 |
TIME | 00:00:00 |
5. Press the JOG , buttons to display “28” and then press the ENTER button.
• The setting item is determined and flashing stops.
<TIME DATE ADJUST> | OFF |
DAYLIGHT SAVING | |
>>DAY | 28 |
MONTH | 01 |
YEAR | 2003 |
TIME | 00:00:00 |
6.Repeat steps 4 and 5 to set “MONTH” and “YEAR.”
7.Press the JOG 
,
buttons to move the cursor to “TIME” and then press the ENTER button twice.
•The setting item of hour digit is highlighted when the ENTER button is pressed once. When the button is pressed again, the background turns red and flashes.
<TIME DATE ADJUST> |
| OFF |
DAYLIGHT SAVING |
| |
DAY |
| 28 |
MONTH |
| 10 |
YEAR |
| 2003 |
TIME | 00:00:00 | |
8. Press the JOG , buttons to display “18” and then press the ENTER button.
• The setting item is determined and flashing stops.
<TIME DATE ADJUST> |
| OFF |
DAYLIGHT SAVING |
| |
DAY |
| 28 |
MONTH |
| 10 |
YEAR |
| 2003 |
TIME | 18 | :00:00 |
The time is indicated using the
9.Press the JOG 
button to move the highlighted display to “MINUTE” and press the ENTER button. And then repeat step 8.
10.Repeat step 9 for “SECOND.”
11.Press the ENTER button.
•The setting item is determined and flashing stops.
<TIME DATE ADJUST> | OFF | ||
DAYLIGHT SAVING | |||
DAY |
| 28 | |
MONTH |
| 10 | |
YEAR | 2003 | ||
TIME | 18:30: | 00 |
|
12. Press the CLEAR button or the SET UP button.
♦Present time display
When turning on the power of the unit, the time/date display shown below appears (in case of DISPLAY MODE 3).
For setting other display modes, 
see “DIS- PLAY MODE” on page 34.
During recording, the recorded capacity of HDD is displayed. When recording is stopped, the display is cleared (with the exception of when pausing re- cording). The recorded capacity of HDD appears again after a few moments when recording is started again.
INFORMATION
This unit uses 4 digits to display the year. The available display range is 99 years between 1/1/2001 to 31/12/2099. The unit is also equipped with a function to automatically calculate leap years. The date returns to the year 2001 after 31/12/2099.
♦Recorded capacity display function
Day of | Recorded capacity of |
Day Month Year the week | the HDD |
00:00:00 12.5P 99% A00001
Minute Recording interval
Hour | Second | Alarm recording number |
When “REMAIN HDD” of the <REAR TERMINAL SETTINGS> screen is set to “MAIN” or “SUB,” the recorded capacity of the specified HDD is displayed on the screen. The “%” indicates the ratio of the recorded capacity to the total HDD capacity. The following settings are required to enable this function.
1)Select HDD and set the remaining capacity in the “REMAIN HDD” of the <REAR TERMINAL SETTINGS> screen. (
see page 50).
2)Set “DISPLAY MODE” in the <TIME DATE/DISPLAY SETTINGS> screen to “3.” (
see page 34).
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
24