■REAR TERMINAL SETTINGS
♦MODE OUT 1 to MODE OUT 5
These items are used to output the status of this unit from the MODE OUT terminals on the rear panel. There are 5 MODE OUT terminals. Set output type for each terminal individually.
<REAR | TERMINAL SETTINGS> | OFF | ||
>>MODE | OUT | 1 |
| |
MODE | OUT | 2 |
| OFF |
MODE | OUT | 3 |
| OFF |
MODE | OUT | 4 |
| OFF |
MODE | OUT | 5 |
| OFF |
KEY SOUND |
|
| ON | |
BUZZER |
|
| OFF | |
REMAIN HDD | ||||
CALL OUT SETTINGS |
| 10M | ||
EMERGENCY REC DURATION | ||||
3.To set other terminals, repeat step 2.
4.Press the CLEAR button or the SET UP button.
♦KEY SOUND
This item is used to make button sounds when using the operational buttons.
|
|
|
|
|
|
<REAR | TERMINAL SETTINGS> | OFF | |||
MODE | OUT | 1 |
| ||
MODE | OUT | 2 |
| OFF | |
MODE | OUT | 3 |
| OFF | |
MODE | OUT | 4 |
| OFF | |
MODE | OUT | 5 |
| OFF | |
>>KEY SOUND |
|
| ON | ||
BUZZER |
|
| OFF | ||
REMAIN HDD | |||||
CALL OUT SETTINGS |
| 10M | |||
EMERGENCY REC DURATION | |||||
|
|
|
|
|
|
ENGLISH
Setting (default: “OFF”)
“REC”: Outputs signals during recording.
“PLAY”: Outputs signals during playback.
“REMAIN”: Outputs signals when the remaining HDD capacity reaches the value specified in “REMAIN HDD.”
“POWER”: Outputs signals when the power of the unit turns on.
“MOTION1” to “MOTION4”: Outputs the signal from the specified MODE OUT terminal when detecting motion by a specified camera number. For example, when you set MODE OUT 1 to MOTION 1, the signal is output from the MODE OUT 1 terminal when detecting motion by the camera number 1. Furthermore, the last input of the motion detection maintained for 2 seconds.
“ALARM”: Outputs signals during alarm recording.
“LAN”: Controls ON/OFF of the terminal set to this item via PC by using the specified application.
“CALL OUT”: Outputs CALL OUT signal when the error occurs to the unit. Refer to the table on page 81.
“OFF”: Does not output signal.
Remaining warning from MODE OUT is output only during recording.
1.Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select “REAR TERMINAL SETTINGS” screen.
2.For the desired terminal (from MODE OUT 1 to MODE OUT 5), display the desired setting and then determine such setting.
1.Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select “KEY SOUND” in the <REAR TERMINAL SETTINGS> screen. Display the desired setting and determine such setting.
2.Press the CLEAR button or the SET UP button.
♦BUZZER
This item is used for a buzzer to sound when the remaining HDD capacity reaches the value set in “REMAIN HDD” of the <REAR TERMINAL SETTINGS> screen. Other than the above, it is possible to set the buzzer to sound when starting alarm recording or emergency recording, or when a warning is displayed.
|
|
|
|
|
|
<REAR | TERMINAL SETTINGS> | OFF | |||
MODE | OUT | 1 |
| ||
MODE | OUT | 2 |
| OFF | |
MODE | OUT | 3 |
| OFF | |
MODE | OUT | 4 |
| OFF | |
MODE | OUT | 5 |
| OFF | |
KEY SOUND |
|
| ON | ||
>>BUZZER |
|
| OFF | ||
REMAIN HDD | |||||
CALL OUT SETTINGS |
| 10M | |||
EMERGENCY REC DURATION | |||||
|
|
|
|
|
|
To sound a buzzer only when reaching a specified remaining HDD capacity:
1)Select “REMAIN” for “BUZZER” in the <REAR TERMI- NAL SETTINGS> screen.
2)Set the remaining capacity in “REMAIN HDD” of the <REAR TERMINAL SETTINGS> screen.
To sound a buzzer when reaching the specified remaining HDD capacity and when a warning is displayed:
1)Select “WARNING” for “BUZZER” in the <REAR TER- MINAL SETTINGS> screen.
2)Set the remaining HDD capacity (HDD MAIN REMAIN/ HDD SUB REMAIN) in “CALL OUT SETTINGS” of the <REAR TERMINAL SETTINGS> screen.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
49