<INITIAL SET UP/INFORMATION> (continued)

Setting of “TRANSMISSION MODE” (default: “9600”) “1200,” “2400,” “4800,” “9600,” “19200”

Setting of “DATA BIT LENGTH” (default: “8BIT”) “8BIT,” “7BIT”

Setting of “PARITY BIT” (default: “NONE”) “NONE,” “ODD,” “EVEN”

Setting of “STOP BIT LENGTH” (default: “1BIT”) “1BIT,” “2BIT”

Setting of “DELIMITER” (default: “CR”) “CR,” “CR•LF”

1.Set RS-232C “MODE” to “REMOTE A,” “REMOTE B,” or “REMOTE C.”

2.Select “SETTINGS” and then press the ENTER button.

•The <RS-232C SETTINGS> screen appears.

3.Select the setting to be changed and then press the ENTER button.

•The background of the setting item turns red and flashes.

4.Display the desired setting item and then press the ENTER button.

•The setting item is determined and flashing stops.

5.To make additional changes, repeat steps 3 and 4.

6.Press the CLEAR button or the SET UP button.

♦ETHERNET

This menu is used to set the IP ADDRESS which is to specify the connected recorder, SUB NET MASK, or GATEWAY, and to confirm MAC ADDRESS.

Do not assign “000.000.000.000” to IP address. And do not assign it as the broadcast address. If this address is assigned, communications or any other functions of the recorder unit may not function correctly.

1.Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select “ETHERNET” in the <COMMUNICATION PORT SETTINGS> screen and then press the ENTER button.

•The <ETHERNET> screen appears.

<ETHERNET>￿

192.168.000.100￿

>>IP ADDRESS

SUB NET MASK

255.255.255.000￿

GATEWAY

000.000.000.000￿

E-MAIL ADDRESS￿

SERVICE PORT SETTING￿

ALARM NOTIFICATION SETTING￿

￿

<MAC ADDRESS> ￿ 08-00-70-2E-20-AD￿

PLEASE PRESS SET UP BUTTON￿ TO APPLY NEW SETTING

2.Select the setting to be changed by pressing the JOG , buttons and then press the ENTER button.

•The leftmost number of the setting item is highlighted.

3.Press the JOG , buttons to highlight the number to be changed and then press the ENTER button.

•The background of the selected number turns red and flashes.

4.Press the JOG , buttons to display the desired number and then press the ENTER button.

•The setting item is determined and flashing stops.

•To display the cursor, press the CLEAR button.

5.Repeat steps 2 to 4 to change the other numbers.

The setting cannot be changed during recording. Stop recording to change the setting.

When you change the items in the <ETHERNET> screen, press the SET UP button while the cursor is on the left side of the item. (In this case, the CLEAR button does not function. However, when you change “WARNING,” “ALARM SENS,” “REC MODE,” or “RETRY TIME” in <ALARM NOTIFICATION SETTING> only, the CLEAR button functions.) The unit turns the power off automatically, and then boots- up.

• E-MAIL ADDRESS

This item is used to refer the setting of “SMTP SERVER,” “RECORDER ID,” and “USER ADDRESS.” This menu is for displaying the setting only.

The specified software is required to input “SMTP SERVER,” “RECORDER ID,” and “USER ADDRESS.” Please refer to the instruction manual of the software.

1.Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } <COMMUNICATION PORT SETTING> }Select “E-MAIL ADDRESS” in the <ETHERNET> screen.

•The <E-MAIL ADDRESS> screen appears.

<E-MAIL ADDRESS>￿

SMTP SERVER￿

￿

RECORDER ID￿

￿

USER ADDRESS￿

1￿

2￿

3￿

4￿

5

“E-MAIL ADDRESS” is displayed only first 20 characters.

• SERVICE PORT SETTING

This menu is used to set the port number to connect personal computer.

Do not change the setting without sufficient knowledge about the network setting.

When performing port setting except “WEB,” the specified software is required. Please refer to the instruction manual of the software.

1.Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } <COMMUNICATION PORT SETTINGS> } select “SERVICE PORT SETTING” in the <ETHERNET> screen.

•The <SERVICE PORT SETTING> screen appears.

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

52