Mitsubishi Electronics DX-NT400E Warnings and CALL OUT output

Press and hold WNG1200 the WARNING (MAIN) RESET button. WNG1201

(SUB)

Stop recording. WNG54

Warnings and CALL OUT output

■Warnings and their appropriate countermeasures

#1 Options in the CALL OUT output column:

• Selectable	: selects to output CALL OUT signal or not on the menu screen.
• Fixed	:	outputs CALL OUT signal from the CALL OUT terminal regardless of the menu setting.
• None	:	does not output CALL OUT signal, but displays a warning on the screen.

CALL OUT signal output can be stopped by pressing the WARNING RESET button.

ENGLISH

Warning Display	Status
REC/FULL	• MAIN HDD recordable
	capacity is full.
REC/SUB FULL	• SUB HDD recordable
	capacity is full.
REC/REM	• The remaining HDD
	capacity has reached the
	value set in HDD REMAIN.

Countermeasure	Canceling	Code
	the warning
• When the warning is	Press and hold WNG1100
cancelled, the unit starts	the WARNING
over-writing the oldest data	RESET button. WNG1101
remaining in the hard disk
drive.

• Replace with new HDD.

• Replace with new HDD.

CALL OUT

output page #1

Selectable 47

14-17 Selectable 14-17

NO SIGNAL

(The warning indicates the number of the non-functioning camera. )

IMAGE MODIFIED

SYSTEM ERROR REC/

SYSTEM ERROR PLAY/

SYSTEM ERROR REC/RW

MIRROR

<DEVICE ERROR>

TEMP

FAN

•Video signal was lost for more than 5 seconds during recording.

•Video data that has been altered was played back.

•System error has occurred.

•Error has occurred during writing of data to HDD.

•One HDD could not be detected during mirroring.

•Unable to recognize HDD.

•HDD or HDD tray is connected or attached incorrectly.

•Issued when in a high temperature environment within the tolerance level.

•The fan stops.

• Check whether the unit
and camera are properly
connected, and that electri
-city is on.
• Check whether the video	Output video
signal is being properly	signals.
output.
• Check that whether there	Press and hold
is a camera set for operation	the WARNING
with no video signal input.	RESET button.
	Press and hold	WNG5500
	the WARNING
	RESET button.
• Reboot.	Press and hold	WNG5100
• Check the HDD.	the WARNING	WNG14
	RESET button.
		WNG24
• Check the HDD.	Press and hold	WNG13
	the WARNING
	RESET button.
• Reboot.	Press and hold	WNG6100
	the WARNING
	RESET button.
• Reboot.	Turn off the	WNG6200
	power.
• Check that the HDD or
HDD tray is connected or
attached correctly.
• Turn off the power and	Press and hold	WNG5200
change the installation	the WARNING
condition.	RESET button.
	Lower
	the temperature.
• Turn off the power and	Press and hold	WNG5300
stop usage.	the WARNING
	RESET button.
	Rotate the fan.

#3 Fixed 12

37

25, 26 41-43

Fixed when 47, 48 setting is

“ON”

Fixed -

#2

#2
#2 None	-
Fixed	54, 55
	69
Fixed	54, 55
	14-17
None	-

Fixed -

(NONE)	• Reboots by watchdog	WNG5101
	operation.

-

#2	: (The following numbers are in )	#3 : (The following numbers are in )
00	: A (MASTER) 01 : B (SLAVE)	01 : CAMERA IN 1	02 : CAMERA IN 2
		03 : CAMERA IN 3	04 : CAMERA IN 4

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Warnings and CALL OUT output

81