Troubleshooting

If problems with the unit persist even after you’ve followed the suggestions below, please disconnect the power cord and contact the retailer from whom you purchased the unit.

 

Description of problem

Please consult the following

Page

 

 

 

 

 

The unit is not turned on.

• Is the power cord properly plugged in?

-

 

 

• Is the SIMPLE LOCK or PASSWARD LOCK turned on?

55 to 57

 

 

• Is the unit in timer recording stand-by mode?

45

 

 

• Is the MAIN switch on the rear panel set to “OFF” ?

9

 

Power is on, but the unit

• Is the SIMPLE LOCK or PASSWARD LOCK turned on?

55 to 57

INSTALLATION

does not operate.

• Is the POWER button flashing?

8

 

(The unit cannot be operated when the POWER button is flashing.)

 

 

 

 

 

 

• The safety features may be in operation.

9, 68

 

 

Press the RESET button located on the rear panel using a ballpoint

 

 

 

pen or similar object and then turn the POWER on.

 

 

 

 

 

 

Images are not appearing

• Are the monitor and camera(s) connected correctly?

12

 

on the monitor.

• Is the unit receiving an input signal from the selected camera?

37

 

 

Check this by displaying the SPLIT4 screen display.

 

 

 

 

 

 

The quality of the monitor

• Is the cord connected correctly?

-

 

picture is poor.

• Is the camera’s focus adjusted correctly?

-

 

 

 

 

 

<DEVICE ERROR>

• Check that the HDD is connected or attached correctly, and the

14-17

 

appears on the monitor.

HDD tray is attached correctly.

 

 

 

When the message displays even after the above items are checked,

 

 

 

the connector of the HDD tray may be defective. Consult your dealer.

 

 

 

 

 

 

The unit does not start

• Are the “HDD REPEAT REC MAIN” set to “OFF” or “STANDBY” and47

 

recording.

“HDD REPEAT REC SUB” set to “OFF”?

 

 

 

• The unit begins recording only after the specified recording

25, 26

 

 

interval time.

 

 

 

Was the unit stopped during the specified recording interval time?

 

 

 

 

 

 

The unit does not stop

• Is the SIMPLE LOCK or PASSWARD LOCK turned on?

55 to 57

 

recording.

• During normal recording, alarm recording, and emergency

10

RECORDING

 

recording, press both REC/STOP buttons.

 

 

• Is timer recording in progress?

44, 45

 

 

 

 

To stop timer recording, press both TIMER ON/OFF buttons again.

 

 

 

 

 

 

The unit does not perform

• Are the “HDD REPEAT REC MAIN” and “HDD REPEAT REC

47

 

repeat recording.

SUB” set to “ON”?

 

 

 

 

 

 

The unit does not perform

• Are the date and present time set accurately?

24

 

timer recording.

• Are the recording start-/end-times and the recording interval

44 to 46

 

 

set correctly?

 

 

 

• Are the “HDD REPEAT REC MAIN” set to “OFF” or “STANDBY” and47

 

 

“HDD REPEAT REC SUB” set to “OFF”?

 

 

 

• Is the “A-PPS” in the <RECORD SETTING> set to “- - - - - -”?

42

 

 

• Is the SUB HDD recordable capacity full?

24

 

 

 

 

 

The unit does not perform

• Is the unit in timer recording stand-by mode?

45

 

alarm recording.

• Are the peripheral switches, etc., connected correctly?

12, 13

 

 

 

 

PLAYBACK

The unit does not perform

• Is the SIMPLE LOCK or PASSWARD LOCK turned on?

55 to 57

 

 

playback.

• Has the image data been erased?

54

 

 

• Is the correct playback device selected?

63

 

 

 

 

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Troubleshooting

ENGLISH

79