SENSITIVITY

This item is used to set the sensitivity of detecting the changes of the loaded video data. Video data is sampled every 0.5 second and compared with each video data of

0.5second before for each camera. The sensitivity setting is divided into the 5 levels of difference in brightness.

<MOTION DETECTION

SETTINGS>￿

SELECTION CAMERA NUMBER￿

1

DETECTION MASK SETTING￿

 

>>SENSITIVITY

HIGH••<<<LOW￿

MOTION THRESHOLD

 

5￿

TEST MODE￿

 

OFF

MD LOCK OUT TIME

 

Setting (default: “HIGH • • < < < LOW”)

“HIGH • • • • < LOW,” “HIGH • • • < < LOW,” “HIGH • • < < < LOW,” “HIGH • < < < < LOW,” “HIGH < < < < < LOW”

Sensitivity increases as “<” increases from “HIGH • • • • < LOW” to “HIGH < < < < < LOW.”

To detect the slightest changes, set to

“HIGH < < < < < LOW.” However, detection may not operate properly due to flickering of fluorescent lighting, etc.

1.In “SELECTION CAMERA NUMBER,” select the camera for which the sensitivity is set.

2.Display the desired setting in “SENSITIVITY” and press the ENTER button.

The setting item is determined.

MOTION THRESHOLD

This item is used to set the minimum number of dots for starting the motion detection operation from the number of active dots within the detection area. Motion detection function operates when detecting the change that exceeds the number of dots set as the minimum.

<MOTION DETECTION

SETTINGS>￿

SELECTION CAMERA NUMBER￿

1

DETECTION MASK SETTING￿

 

SENSITIVITY

HIGH••<<<LOW￿

>>MOTION THRESHOLD

 

5￿

TEST MODE￿

 

OFF

MD LOCK OUT TIME

 

1.In “SELECTION CAMERA NUMBER,” select the camera for which the motion threshold is set.

2.Display the desired setting in “MOTION THRESHOLD” and press the ENTER button.

The setting item is determined.

TEST MODE

This item is used to test the motion detection function on the condition you have set.

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

• • • • • • • • • • • • • • •￿

￿

1.In “SELECTION CAMERA NUMBER,” select the camera to be tested.

2.Select “TEST MODE” and press the ENTER button.

The operation test begins.

3.To end “TEST MODE,” press the CLEAR button.

During test operation, active areas of motion detection are displayed using “ • .” “ &” is displayed when the motion which is met the conditions of sensitivity and MD lock out time is detected. If the motion detection does not operate properly, set the conditions again.

This test is executed under the condition you have set in the <MOTION DETECTION SETTINGS> screen.

ENGLISH

Setting (default: “5”)

“1,” “2,” “3,” “4,” “5,”• • • • • ,“191,” “192”

Set MOTION THRESHOLD to the number less than the number set as the active dots in the detection area. The motion detection function does not operate when setting MOTION THRESHOLD to a value exceeds that number.

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations

39