Muratec F-98 operating instructions Programming a F-Code transmission, P3Fax Number 5552208

Press ENTER, ENTER.

Beyond the basics

6 Now, while you can still see the fax number on the LCD, press COM-OPTIONS three times and then press ENTER.

7 If you want the polling to begin immediately every time you press the key, press ENTER and skip to step 10.

If you want to delay the polling (perhaps to take advantage of lower phone

rates), press COM-OPTIONS,ENTER.

8 There’s a choice to make. Instruct your fax to carry out this delayed command in one of the following ways:

Option 1: Perform the command once at a certain time on a certain day of the month. (For example, “Do this at 5:05 PM on the 30th.”)

To select this option, use the numeric keypad to enter the date and time when the fax should perform the command:

Delayed

Enter Time: 30/17:05

Option 2: Perform the command at a certain time each day you press the key. (For example, “Do this at 5:05 PM today.”)

To select this option, use the numeric keypad to enter 0, 0 (i. e., 00), and then the time when the fax could perform the command:

Delayed

Enter Time: 00/17:05

9

10 The LCD now displays the next programmable one-touch key.

If you do not want to enter or change any other key’s programming, press STOP to return your machine to its usual standby mode.

If you do want to enter or change this key’s programming, go back to step 3. If you want to enter or change another key’s programming, go back to step 2.

Programming a F-Code transmission

Note: To erase a programmable one-touch key, refer to page 2.41.

Note: For this operation to work, two things must be true:

•You must know how the remote fax is using each F-Code (ITU-T-standard sub-addressing/password) box to which you’re transmitting — for exam- ple, as a security box (different makers may use slightly different terms, but the concepts are the same).

•You must know the remote fax’s ITU-Tsub-address and password number for each box to which you want to transmit.

To program an F-Code transmission into a programmable one-touch key:

1 Press PROGRAM, C, 1, ENTER. The LCD either shows:

Select Program No.

P1:No Number Stored

… or indicates a command is already programmed into this key.

If P1 is the key you want to program, skip to step 3. (However, our examples from here will say “P3” rather than “P1.”)

2 Select the key in which you want to program a command or change a previ- ously stored command and then press it. Here, we’ve selected P3.

Select Program No.

P3:No Number Stored

3 If you change your mind and want to select a different programmable one- touch key, go back to step 2 before going on to step 4.

4 Press ENTER. The LCD now shows either

P3:Fax Number	or	P3:Fax Number
_		9-5552208_

5 Use the numeric keypad to enter the number exactly as your machine should dial it, including whatever codes your phone system may require. The num- ber can be up to 40 characters in length:

P3:Fax Number 9-5558422_

Your display can show only 20 characters at a time. To view characters beyond those 20 (such as with an international long-distance number), press to scroll leftward or to scroll rightward.

Important: Do not press ENTER.

Note: If you make a mistake or want to erase characters entered in a previ- ous setting, press CANCEL to erase leftward. Or, if you want to change just one character in the number, press to move the cursor leftward, or to move it rightward, to that character and press CANCEL to erase it. Then re-enter until the number is just as you want it.

6 Now, while you still can see the fax number on the LCD, press COM-OPTIONSfour times and then press ENTER. The LCD shows:

Enter Sub-Address

_

2.38