Manuals / Nortel Networks / Computer Equipment / Switch

Nortel Networks CVX 600 manual Ethernet 10/100BASE-TX Interface Cable Specifications

Models: CVX 600

1 168

Download 168 pages 8.82 Kb

Page 153

Technical Specifications

Cable Specifications

Ethernet 10/100BASE-TX Interface Cable Specifications

The Ethernet 10/100BASE-TX interfaces provide unshielded twisted pair (UTP) support.

The following figure shows the Ethernet 10/100BASE-TX interface connector:

8

7

6

5

4

3

2

1

CVX-0103A

Ethernet 10/100BASE-TX Pin and Signal Assignments

The following table lists the pin and signal assignments for these interfaces:

Pin	Standard Interface Signal	Crossover

1	TD+ (Transmit to UTP)	RD+ (Receive from UTP)

2	TD- (Transmit to UTP)	RD- (Receive from UTP)

3	RD+ (Receive from UTP)	TD+ (Transmit to UTP)

4	Not used	Not used

5	Not used	Not used

6	RD- (Receive from UTP)	TD- (Transmit to UTP)

7	Not used	Not used

8	Not used	Not used

296-1011-202 Rel. 5.0, Doc. Rev. 02.01

A-11

Image 153

Nortel Networks CVX 600 Ethernet 10/100BASE-TX Interface Cable Specifications, Pin Standard Interface Signal Crossover

Contents

CVX 600 Multi-Service Access Switch Page Interface Service Code Facility Code FCC Radio Frequency Notice for the CVX 600 Access SwitchA. Requirements FCC Part 68 General InformationAustralian Requirements FCC and Telephone Company Procedures and RequirementsCanadian Requirements UL Listing and CSA Certification U.S. and CanadaCanada CS-03 Rè gles et rè glements European RequirementsEMI/EN 55 022 Statement EC Declaration of ConformityJapan/Nippon Requirements Only Voluntary Control Council for Interference Vcci StatementJate Requirements General Warnings DC Power Supply WarningsLithium Battery Caution Contents Chapter Chassis Installation Chapter Chassis Connections Connecting Chassis to an AC Power Source Chapter Replacing CVX 600 Components Appendix a Technical Specifications Tool and Parts Needed Page Introduction About This GuideTopics This preface covers the following topicsThis guide contains the following chapters and appendixes Chapters and Appendixes in This GuideAccessing Software Upgrades Accessing Related DocumentationInformation About CVX Products About This ReleaseEquipment Problems Customer ServicesTechnical Support Product DamageThis chapter describes how to install the CVX 600 chassis About This ChapterThis chapter covers the following topics Where to Install Remote Access ConfigurationCVX 600 Chassis Overview DescriptionFollowing figure shows the front of the CVX 600 chassis Front View of CVX 600 ChassisFollowing figure shows the rear of the CVX 600 chassis Rear View of CVX 600 ChassisOverview Preparing the Site for the InstallationReference Mounting OptionsFt Telco rack Surface mounted Mounting the CVX 600 in a Rack Rack PlacementRack Capacity Rack RequirementsCeiling Requirements Size and Weight ConsiderationsNortel Networks PTE 2000 Rack Properly ventilated Well lightedReference Anchor KitsKit Number Earthquake Zone Floor Type Compliance Space Requirements Following table lists the PTE 2000 racks and dimensionsFlooring Requirements Depth for DrillingRack Cooling Requirements Access ConsiderationsAC and DC Power CVX 600 uses either an AC or DC power sourceAC Power Option DC Power Option Preparing for the CVX 600 Installation Unpacking the ShipmentStep Action Checking the Shipment Tools and Equipment Needed Service ConsoleTools Cables and Cable TiesMounting Hardware Positioning the Chassis on a Flat Surface Installing the CVX 600 ChassisTo install the feet, follow these steps Installing the Feet on the Bottom of the ChassisMounting the Chassis in a Rack Mounting flanges are preinstalled on the chassisTelco and EIA Rack Hole Spacing Hardware Needed to Complete the Chassis Installation To install the chassis, follow these steps Installing the ChassisUse a Phillips screwdriver to tighten the screws Chapter Chassis Connections Connecting Alarms Alarm CategoriesAlarm Possible Cause Alarm Type Severity Description Alarm TypesPtraceStringExpect attribute StraceStringExpect attributeATM Pvpc To connect alarms to the terminal block, follow these steps ProcedureOptical OC3/STM1 Connecting Network CablesPlug the UTP connectors into the receptacles External clocking Device optional Connecting to DS1/T1 InterfacesConnecting to E1 Interfaces To connect to DS3 interfaces, follow this step Connecting to DS3 InterfacesPlug the cable connector into the Hssi interface receptacle Connecting to the Hssi InterfaceConnecting to the OC3/STM1 Interface Connecting an Optical Cable To connect an optical cable, follow these stepsOptical DAC-LTM Optical SCC-II-LTM Connect toOptical port Connecting Power to the Chassis Before You StartRequirements Use the compression terminal Grounding the ChassisUsing the NEBS-Compliant Dual-Connector Posts Using the Compression Terminal Use a flat-tip screwdriver to loosen the locking screw Prerequisites Connecting to a Customer-Supplied DC Power SourceRemove the nuts from the posts using a 3/8-inch nutdriver Black cable to Return Tighten screws to 6 in-lb Next StepConnecting Chassis to an AC Power Source AC power source is only for the AC chassis optionConnecting the Power Cords Next Step AC power cordsCable Mounts Routing the CablesSuggested Use Locations of Cable MountsIntroduction Routing Fiber Optic CablesMinimum Radius Rack Standoff BracketsInstalling and Removing the Flash Memory Cards To insert a flash memory card, follow these steps Inserting a Flash Memory CardTo remove a flash memory card, follow these steps Removing a Flash Memory CardConnecting Equipment to the Console Port Parameter Value Connecting a TerminalDB-9 to DB-9 console cable DB-9 port On terminal Connecting a PC DB-9 port on PC DB-9 to DB-9 console cable Modem Parameter Value/State Connecting a ModemModem AT or Hayes compatible Sample Hardware Arrangement for CVX Switches Connecting a Terminal ServerRecommendations Rear Connections for Sample Hardware ArrangementConnecting a Remote Device Using an Ethernet Port Connecting Equipment to a Local Ethernet PortTo apply power to the CVX 600, follow these steps Applying Power to the CVXSCC-HSSI-SM, SCC-HSSI-RLTM Checking the LEDsFollowing figure shows the LEDs on the SCC-SM and SCC-RLTM SCC-SM, SCC-RLTM Ethernet 10/100 Mb/s portsFollowing table describes the LEDs on the SCC-SM LEDs on the SCC-SMLEDs on the SCC-RLTM Following table describes the LEDs on the SCC-RLTMSCC-HSSI-SM, SCC-HSSI-RLTM Following table describes the LEDs on the SCC-HSSI-SM LEDs on the SCC-HSSI-SMLEDs on the SCC-HSSI-RLTM Following table describes the LEDs on the SCC-HSSI-RLTMSCC-II-LTM Optical SCC-IIFollowing table describes the LEDs on the Optical SCC-II-SM LEDs on the Optical SCC-II-SMFollowing table describes the LEDs on the Optical SCC-II-LTM LEDs on the Optical SCC-II-LTMFollowing figure shows the LEDs on the Optical DAC-SM Optical DACLEDs on the Optical DAC-SM Following table describes the LEDs on the Optical DAC-SMDAC-SM LEDs LEDs on DAC-SM Following figure shows the LEDs on the MAC-SM MAC-SM LEDsLEDs on the MAC-SM Following table describes the LEDs on the MAC-SMReplacing CVX 600 Components Attaching the Antistatic Wrist Strap How to Attach the Wrist StrapLocation of Wrist Strap Purpose of Wrist StrapReplacing CVX 600 Components Replacing Modules and Filler Panels Removing and Installing Filler PanelsTo remove a rear filler panel, follow these steps Removing a Rear Filler PanelReplacing Modules and Filler Panels To install a rear filler panel, follow these stepsTo remove a front filler panel, follow these steps Removing a Front Filler PanelTo install a front filler panel, follow these steps Installing a Front Filler PanelEjector At an Close ejectors Replacing the SCC-SM To remove the SCC-SM, follow these steps Removing the SCC-SMCVX-0150C To install an SCC-SM, follow these steps Installing an SCC-SMClose ejector levers Replacing the SCC-LTM/RLTM Removing the SCC-LTM or SCC-RLTMTo remove the SCC-LTM or SCC-RLTM, follow these steps CVX-0154B CVX-0155B To install an SCC-LTM or SCC-RLTM, follow these steps Installing an SCC-LTM or SCC-RLTMCVX-0157C Replacement Procedure Replacing Other Service ModulesTo remove a MAC or DAC-SM, follow these steps Removing a Service ModuleCVX-0159B To install a MAC or DAC-SM, follow these steps Installing a Service ModuleFor information about the LEDs, see Checking the LEDs on References Replacing the DAC-LTM/-RLTMTo remove a DAC-LTM or DAC-RLTM, follow these steps Removing a DAC-LTM or DAC-RLTMCVX-0163C Installing a DAC-LTM or DAC-RLTM CVX-0165B Replacing the Fan Module To remove the fan module, follow these steps Removing the Fan ModuleCVX-0167B To install a fan module, follow these steps Installing a Fan ModuleCVX-0169B Replacing a PDU Module Removing the PDU ModuleTo remove the PDU module, follow these steps CVX-0171B To install a PDU module, follow these steps Installing a PDU ModuleLocked Unlocked Replacing a Power Module Removing the Power ModuleTo remove a power module, follow these steps CVX-0215B To install a power module, follow these steps Installing a Power ModuleVerify that the LED is on Rel .0, Doc. Rev How to Order Ordering Replacement ComponentsThis appendix covers the following topics About This AppendixDimensions, Weight, Slot Capacity Chassis Specifications and ClearancesClearance Attribute MeasurementSpecifications Environmental SpecificationsNeed for Ventilation Cooling RequirementsMethods of Cooling AirflowCVX 600 Requirements Electromagnetic Emissions and Radio FrequencyCable Specifications Cables Supplied by Nortel NetworksCables Supplied by the Customer Management Console Cable Specifications DB-9 Pin and Signal AssignmentsPin Signal To Signal Pin on DB-9 Connector Signal Name Pin on DB-25 Connector DB-9 to DB-25 Pin and Signal AssignmentsHssi DTE to DCE Pin and Signal Assignments Following figure shows the Hssi connectorNortel Networks Termination Remote Termination Pin Signal Hssi InterfaceCable Specifications Ethernet 10/100BASE-TX Interface Cable Specifications Ethernet 10/100BASE-TX Pin and Signal AssignmentsPin Standard Interface Signal Crossover E1 and T1 Interface Line Specifications RJ-45 Pin and Signal AssignmentsPin Standard Interface Signal E1, T1 Signal E1 and T1 Shielded Cable Specifications DS3 Coaxial Cable SpecificationsOptical Cable Specifications Tool and Parts Needed Tandem CVX to RAS CVX Crossover CablePin Data FromRJ-45 Pin Numbering Following figure shows the numbering of the RJ-45 connectorAlarm Interface Connector Audible and Visual Alarm Interface SpecificationsSignals Position Audible Signal Visual SignalPower Options Power SpecificationsAC Power Requirements DC Power RequirementsInterface Description SCC-LTM/-RLTM InterfacesDAC-LTM/-RLTM External Clock Interface Page Index Index-2 Rel .0, Doc. Rev Index-3 Page Page CVX 600 Multi-Service Access Switch