A. Requirements | Nortel Networks CVX 600 specs

Regulatory and Safety

Regulatory Information

U.S.A. Requirements

FCC Radio Frequency Notice for the CVX 600 Access Switch

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Part 68 General Information

This equipment complies with Part 68 of the FCC rules. This equipment uses the following USOC RJ-48 jacks:

Interface		Service Code	Facility Code

1.544	Mb/s superframe format (SF) without	6.0N	04DU9-BN
line power

1.544	Mb/s superframe format (SF) and	6.0N	04DU9-DN
B8ZS without line power

1.544	Mb/s ANSI extended superframe	6.0N	04DU9-1KN
format (ESF) without line power

1.544	Mb/s ANSI extended superframe	6.0N	04DU9-1SN
format (ESF) and B8ZS without line power

296-1011-202 Rel. 5.0, Doc. Rev. 02.01

iii

Image 3

Nortel Networks manual A. Requirements, FCC Radio Frequency Notice for the CVX 600 Access Switch

Contents

CVX 600 Multi-Service Access Switch Page FCC Part 68 General Information FCC Radio Frequency Notice for the CVX 600 Access SwitchInterface Service Code Facility Code A. Requirements UL Listing and CSA Certification U.S. and Canada FCC and Telephone Company Procedures and RequirementsAustralian Requirements Canadian Requirements EC Declaration of Conformity European RequirementsCanada CS-03 Rè gles et rè glements EMI/EN 55 022 Statement Japan/Nippon Requirements Only Voluntary Control Council for Interference Vcci StatementJate Requirements General Warnings DC Power Supply Warnings Lithium Battery Caution Contents Chapter Chassis Installation Chapter Chassis Connections Connecting Chassis to an AC Power Source Chapter Replacing CVX 600 Components Appendix a Technical Specifications Tool and Parts Needed Page This preface covers the following topics About This GuideIntroduction Topics This guide contains the following chapters and appendixes Chapters and Appendixes in This Guide About This Release Accessing Related DocumentationAccessing Software Upgrades Information About CVX Products Product Damage Customer ServicesEquipment Problems Technical Support This chapter describes how to install the CVX 600 chassis About This ChapterThis chapter covers the following topics Description Remote Access ConfigurationWhere to Install CVX 600 Chassis Overview Following figure shows the front of the CVX 600 chassis Front View of CVX 600 Chassis Following figure shows the rear of the CVX 600 chassis Rear View of CVX 600 Chassis Mounting Options Preparing the Site for the InstallationOverview Reference Ft Telco rack Surface mounted Rack Requirements Rack PlacementMounting the CVX 600 in a Rack Rack Capacity Properly ventilated Well lighted Size and Weight ConsiderationsCeiling Requirements Nortel Networks PTE 2000 Rack Reference Anchor KitsKit Number Earthquake Zone Floor Type Compliance Depth for Drilling Following table lists the PTE 2000 racks and dimensionsSpace Requirements Flooring Requirements Rack Cooling Requirements Access Considerations AC and DC Power CVX 600 uses either an AC or DC power sourceAC Power Option DC Power Option Preparing for the CVX 600 Installation Unpacking the ShipmentStep Action Checking the Shipment Cables and Cable Ties Service ConsoleTools and Equipment Needed Tools Mounting Hardware Positioning the Chassis on a Flat Surface Installing the CVX 600 Chassis To install the feet, follow these steps Installing the Feet on the Bottom of the Chassis Mounting the Chassis in a Rack Mounting flanges are preinstalled on the chassis Telco and EIA Rack Hole Spacing Hardware Needed to Complete the Chassis Installation To install the chassis, follow these steps Installing the Chassis Use a Phillips screwdriver to tighten the screws Chapter Chassis Connections Connecting Alarms Alarm CategoriesAlarm Possible Cause Alarm Type Severity Description Alarm Types PtraceStringExpect attribute StraceStringExpect attribute ATM Pvpc To connect alarms to the terminal block, follow these steps Procedure Optical OC3/STM1 Connecting Network Cables Plug the UTP connectors into the receptacles External clocking Device optional Connecting to DS1/T1 Interfaces Connecting to E1 Interfaces To connect to DS3 interfaces, follow this step Connecting to DS3 Interfaces Plug the cable connector into the Hssi interface receptacle Connecting to the Hssi Interface Connecting to the OC3/STM1 Interface Connecting an Optical Cable To connect an optical cable, follow these stepsOptical DAC-LTM Optical SCC-II-LTM Connect toOptical port Connecting Power to the Chassis Before You StartRequirements Use the compression terminal Grounding the Chassis Using the NEBS-Compliant Dual-Connector Posts Using the Compression Terminal Use a flat-tip screwdriver to loosen the locking screw Prerequisites Connecting to a Customer-Supplied DC Power Source Remove the nuts from the posts using a 3/8-inch nutdriver Black cable to Return Tighten screws to 6 in-lb Next Step Connecting Chassis to an AC Power Source AC power source is only for the AC chassis optionConnecting the Power Cords Next Step AC power cords Locations of Cable Mounts Routing the CablesCable Mounts Suggested Use Rack Standoff Brackets Routing Fiber Optic CablesIntroduction Minimum Radius Installing and Removing the Flash Memory Cards To insert a flash memory card, follow these steps Inserting a Flash Memory Card To remove a flash memory card, follow these steps Removing a Flash Memory Card Connecting Equipment to the Console Port Parameter Value Connecting a Terminal DB-9 to DB-9 console cable DB-9 port On terminal Connecting a PC DB-9 port on PC DB-9 to DB-9 console cable Modem Parameter Value/State Connecting a Modem Modem AT or Hayes compatible Sample Hardware Arrangement for CVX Switches Connecting a Terminal Server Recommendations Rear Connections for Sample Hardware Arrangement Connecting a Remote Device Using an Ethernet Port Connecting Equipment to a Local Ethernet Port To apply power to the CVX 600, follow these steps Applying Power to the CVX SCC-HSSI-SM, SCC-HSSI-RLTM Checking the LEDs Following figure shows the LEDs on the SCC-SM and SCC-RLTM SCC-SM, SCC-RLTM Ethernet 10/100 Mb/s ports Following table describes the LEDs on the SCC-RLTM LEDs on the SCC-SMFollowing table describes the LEDs on the SCC-SM LEDs on the SCC-RLTM SCC-HSSI-SM, SCC-HSSI-RLTM Following table describes the LEDs on the SCC-HSSI-RLTM LEDs on the SCC-HSSI-SMFollowing table describes the LEDs on the SCC-HSSI-SM LEDs on the SCC-HSSI-RLTM SCC-II-LTM Optical SCC-II Following table describes the LEDs on the Optical SCC-II-SM LEDs on the Optical SCC-II-SM Following table describes the LEDs on the Optical SCC-II-LTM LEDs on the Optical SCC-II-LTM Following table describes the LEDs on the Optical DAC-SM Optical DACFollowing figure shows the LEDs on the Optical DAC-SM LEDs on the Optical DAC-SM DAC-SM LEDs LEDs on DAC-SM Following table describes the LEDs on the MAC-SM MAC-SM LEDsFollowing figure shows the LEDs on the MAC-SM LEDs on the MAC-SM Replacing CVX 600 Components Purpose of Wrist Strap How to Attach the Wrist StrapAttaching the Antistatic Wrist Strap Location of Wrist Strap Replacing CVX 600 Components Replacing Modules and Filler Panels Removing and Installing Filler Panels To remove a rear filler panel, follow these steps Removing a Rear Filler Panel Replacing Modules and Filler Panels To install a rear filler panel, follow these steps To remove a front filler panel, follow these steps Removing a Front Filler Panel To install a front filler panel, follow these steps Installing a Front Filler Panel Ejector At an Close ejectors Replacing the SCC-SM To remove the SCC-SM, follow these steps Removing the SCC-SM CVX-0150C To install an SCC-SM, follow these steps Installing an SCC-SM Close ejector levers Replacing the SCC-LTM/RLTM Removing the SCC-LTM or SCC-RLTMTo remove the SCC-LTM or SCC-RLTM, follow these steps CVX-0154B CVX-0155B To install an SCC-LTM or SCC-RLTM, follow these steps Installing an SCC-LTM or SCC-RLTM CVX-0157C Replacement Procedure Replacing Other Service Modules To remove a MAC or DAC-SM, follow these steps Removing a Service Module CVX-0159B To install a MAC or DAC-SM, follow these steps Installing a Service Module For information about the LEDs, see Checking the LEDs on References Replacing the DAC-LTM/-RLTM To remove a DAC-LTM or DAC-RLTM, follow these steps Removing a DAC-LTM or DAC-RLTM CVX-0163C Installing a DAC-LTM or DAC-RLTM CVX-0165B Replacing the Fan Module To remove the fan module, follow these steps Removing the Fan Module CVX-0167B To install a fan module, follow these steps Installing a Fan Module CVX-0169B Replacing a PDU Module Removing the PDU ModuleTo remove the PDU module, follow these steps CVX-0171B To install a PDU module, follow these steps Installing a PDU Module Locked Unlocked Replacing a Power Module Removing the Power ModuleTo remove a power module, follow these steps CVX-0215B To install a power module, follow these steps Installing a Power Module Verify that the LED is on Rel .0, Doc. Rev How to Order Ordering Replacement Components This appendix covers the following topics About This Appendix Attribute Measurement Chassis Specifications and ClearancesDimensions, Weight, Slot Capacity Clearance Specifications Environmental Specifications Airflow Cooling RequirementsNeed for Ventilation Methods of Cooling CVX 600 Requirements Electromagnetic Emissions and Radio Frequency Cable Specifications Cables Supplied by Nortel NetworksCables Supplied by the Customer Management Console Cable Specifications DB-9 Pin and Signal AssignmentsPin Signal To Signal Pin on DB-9 Connector Signal Name Pin on DB-25 Connector DB-9 to DB-25 Pin and Signal Assignments Hssi Interface Following figure shows the Hssi connectorHssi DTE to DCE Pin and Signal Assignments Nortel Networks Termination Remote Termination Pin Signal Cable Specifications Ethernet 10/100BASE-TX Interface Cable Specifications Ethernet 10/100BASE-TX Pin and Signal AssignmentsPin Standard Interface Signal Crossover E1 and T1 Interface Line Specifications RJ-45 Pin and Signal AssignmentsPin Standard Interface Signal E1, T1 Signal E1 and T1 Shielded Cable Specifications DS3 Coaxial Cable SpecificationsOptical Cable Specifications From Tandem CVX to RAS CVX Crossover CableTool and Parts Needed Pin Data RJ-45 Pin Numbering Following figure shows the numbering of the RJ-45 connector Position Audible Signal Visual Signal Audible and Visual Alarm Interface SpecificationsAlarm Interface Connector Signals DC Power Requirements Power SpecificationsPower Options AC Power Requirements Interface Description SCC-LTM/-RLTM Interfaces DAC-LTM/-RLTM External Clock Interface Page Index Index-2 Rel .0, Doc. Rev Index-3 Page Page CVX 600 Multi-Service Access Switch