Manuals / Panasonic / Computer Equipment / Laptop

Panasonic AJ-LT85P manual Specifications, General Video, Digital, Analog Composite In/Out

Models: AJ-LT85P

1 76

Download 76 pages 10.73 Kb

Page 74

SPECIFICATIONS

GENERAL

VIDEO


	Rating input: DC 12V 8.5A
							DVCPRO

Recording format:
Recording tracks							Digital video
							Time code;	Recorded in sub-code area
							Digital audio;	2 channels
							Cue signal;	1 track
							Control (CTL);	1 track
Tape speed:							33.820 mm/sec.
Recording time:							126 min. (with AJ-P126LP tape)
							66 min. (with AJ-P66MP tape)
Tape used:							1/4" thin magnetic layer metal tape
FF/REW time:							Less than 3.5 min. (with AJ-P126LP tape)
Editing accuracy:							±0 frame (with time code)
Tape timer accuracy:							±2 frame (per event when continuous CTL signal is used)
Servo lock time:							Less than 0.5 sec.
Ambient operating temperature:							41°F to 104°F (5°C to 40°C)
Ambient operating humidity:							10% to 85% (no condensation)
Dimensions:							16-3/4" (W)×4-3/4" (H)×17-1/4" (D) (424×120×435 mm)
Weight:							25.74 lb (11.7 kg)

	DIGITAL
Sampling frequency:							Y; 13.5 MHz,
							PB/PR; 3.375 MHz
Quantization:							8 bits
Error correction:							Reed-Solomon codes

	ANALOG COMPOSITE IN/OUT
Video band range:							Y; 30 Hz – 4.5 MHz (±1dB)
DG:							Less than 6%
DP:							Less than 4.5°
Y/C delay:							Less than 20 nsec
K factor:							Less than 2%
Analog composite input:							BNC×2 (VTR1, VTR2), 75 ohms
REF video input:							BNC×2 (loop-through), 75 ohms, automatic
Analog composite output:							BNC×2 (VTR1, VTR2), 75 ohms
Monitor output:							BNC×2 (VTR1, VTR2), 75 ohms, superimpose ON/OFF

	ANALOG COMPONENT OUT					(during playback of standard recording tape)
Video band:							Y; 30 Hz – 5.5 MHz (±1 dB)
							PB, PR; 30 Hz – 1.3 MHz (±1.5 dB)
Analog component output:							BNC×6 (Y, PB, PR, VTR1, VTR2), 75 ohms
							Y connector is switched with the analog composite
							output connector.

	VIDEO OUTPUT SIGNAL
Video gain:							More than ±3dB
Chroma gain:							More than ±3dB
Hue:							More than ±25°
Set up:							±10 IRE
H phase:							More than ±1.5∝sec
SC phase (COARSE):							360°
SC phase (FINE):							90°

74

Image 74

Panasonic AJ-LT85P manual Specifications, General Video, Digital, Analog Composite In/Out, Analog Component Out

Contents

DIGITAL VIDEO CASSETTE Operating InstructionsAJ-P Lap Top EditorFOR YOUR SAFETY FCC NoteCONTENTS Volume controls FeaturesCompact size and light weight 9-pin remote connectors ⋅2Controls and their functions CONTROLS AND THEIR FUNCTIONS1 Liquid-crystal monitor section w COUNTER/REMAIN switchCONTROLS AND THEIR FUNCTIONS 2 Counter display section1 2 3 5 6 7 8 9 0 q w e r EDIT REC INHy AUDIO MONITOR switch for both VTR1 and VTR2 3 Front Keyboard Switchesq POWER switch w REC INHIBIT switchconnector Level Controlsi AUDIO SWAP switch for both VTR1 and VTR2 connectorw RESET button 4 Player/Recorder Control Section5 VTR Control Section for both VTR1 and VTR2 CONTROLS AND THEIR FUNCTIONSi RESET button 6 Edit Mode Setting Section1 2 3 4 5 6 CONTROLS AND THEIR FUNCTIONSCONTROLS AND THEIR FUNCTIONS 7 Automatic Editing Control Sectiont COUNTER switchs Controls and their functionsi OUT button for both VTR1 and VTR2 CONTROLS AND THEIR FUNCTIONSu IN button for both VTR1 and VTR2 o PREVIEW/REVIEW button10 Top Section 8 Side Panel Section for both VTR1 and VTR29 Front Section 5 4 3 29 8 q q 7 Connector Section for both VTR1 and VTR2y 2 3 r 5 6 2 4 t 5 q DC IN socket XLR 4P DC power input socketOPENING AND CLOSING THE LAPTOP Opening andUse of Panasonic consumer DV cassette tapes is recommended COMPATIBLE TAPESPrecautions for playing back consumer-use DV tapes/DVCAM tapes System connections SYSTEM CONNECTIONSConnections for transmission Microwave transmitter AC adaptor2. Recording different signals on 2 VTRs Backup recording using 2 VTRs1. Recording the same signal on 2VTRs System applicationsSwitch setting OPERATION MODE EXT EffectorEditing controller SYSTEM CONNECTIONSSYSTEM CONNECTIONS Using two VTRs as source units for AB roll editingSwitcher System applicationsAJ-LT85 When using an external VTR as the editing source unitExternal VTR System applicationsTo return to the regular mode from the set-up menu mode To change a settingTo store a setting in the memory User default settings and factory settingsDetailed description of set-up menus DETAILED DESCRIPTION OF SET-UP MENUSBASIC OPERATION DETAILED DESCRIPTION OF SET-UP MENUSDetailed description of set-up menus DETAILED DESCRIPTION OF SET-UP MENUSOPERATION INTERFACE DETAILED DESCRIPTION OF SET-UP MENUSDetailed description of set-up menus EDITDETAILED DESCRIPTION OF SET-UP MENUS DETAILED DESCRIPTION OF SET-UP MENUS EDITTAPE PROTECT DETAILED DESCRIPTION OF SET-UP MENUSTIME CODE DETAILED DESCRIPTION OF SET-UP MENUSDetailed DETAILED DESCRIPTION OF SET-UP MENUSTIME CODE descriptionVIDEO DETAILED DESCRIPTION OF SET-UP MENUSDetailed description of set-up menus AUDIODETAILED DESCRIPTION OF SET-UP MENUS DETAILED DESCRIPTION OF SET-UP MENUS AUDIODetailed description of set-up menus SYSTEMDETAILED DESCRIPTION OF SET-UP MENUS PREPARATION OF EDITING TAPE 1st edit Standard modeBASIC FLOW OF EDITING OPERATIONS PreviewTYPES OF EDIT MODES AND ILLUSTRATIONS Assemble edit modeInsert edit mode Split editingCut editing procedure CUT EDITING PROCEDURE1. Edit mode selection Search dialCUT EDITING PROCEDURE 2. Edit point registrationTo produce a still picture of the desired scene During normal playback press the STILL buttonTo check the edit point image Edit point checking, revising and clearingTo check the edit points To check the total timeTo suspend preview and execute automatic editing When preview is executedTo recall the contents of the previous preview CUT EDITING PROCEDURECut editing procedure3. Editing execution CUT EDITING PROCEDURETo suspend the review, press the ALL STOP button CUT EDITING PROCEDUREReview Revising an edit IN point AUDIO SPLIT EDITING PROCEDUREAudio split editing procedure Displaying the audio split amountDisplaying the video split amount VIDEO SPLIT EDITING PROCEDURECorrecting an edit IN point When executing editing without preview EDITING BY EDIT IN POINT SETTING ONLYEditing by edit IN point setting only STILL PICTURE EDITINGAUTO TAG EDITING TRACK FUNCTIONTC JUMP FUNCTION TC jump functionWhen “00” appears as the event number How to register eventsWhen an unregistered event number displayed as “n” is registered EVENT EDITINGCalling an event Accessing an event prior to the event now displayedAccessing the event ahead of the event now displayed Event editingClearing all the events initializing the EDL Accessing a registered event and revising its dataRevising and clearing events Executing event editingDisplaying event numbers Calling the previously previewed contentsEDIT DATA MANAGEMENT EDL Edit data management EDLSteps taken for loading EDIT DATA DUMPING TO/LOADING FROM AN EXTERNAL DEVICESteps taken for dumping 3 To send data from the RS-232C connector of an external device Reference External device settings and communication methods2 To receive data using the RS-232C connector of an external device Edit data dumping to/loading from an external device1. Editing mode Reference Concerning the EDL format3. Editing mode Editing modeAUDIO RECORDING SWAP FUNCTION VTR2 only Audio recording swap function VTR2 onlyCONNECTIONS WITH THE AJ-YA752 AUDIO MEMORY UNIT Time codes TC and TIME CODES TC and USER BITS UBTime code generator TCG and user bit generator UBG modes Time codesTime code generator TCG and user bit generator UBG mode setting TIME CODES TC and USER BITS UB1 AUTO EDIT mode VTR2 only Time code generator TCG and user bit generator UBG mode tableTime codes TC and User bits UB 2 Mode other than AUTO EDIT VTR1 and VTR2REC SAME function VITC output specificationsTC OUT LTC output specifications Turning on the REC SAME functionSwitcher ENCODER ADJUSTMENTSTo adjust the encoder using the laptop Encorder adjustmentsWaveform on WFM ENCODER ADJUSTMENTS# Conduct the adjustments using a discrete source unit Waveform on VSCAdjustment in display section LIQUID-CRYSTAL TV MONITOR ADJUSTMENTSLiquid-crystal TV monitor adjustments Adjustments in set-up menu modeBlock SUPERIMPOSE SCREEN DISPLAYSTo superimpose displays BlockCharacters displayed What is displayedSuperimpose screen displays CTL counter displayAUDIO CONNECTOR SIGNALSVIDEO DC INDetails of error ERROR MESSAGESError No VTR operationDetails of error ERROR MESSAGESError No Forced POWER OFFDIAG-MENU OPERATIONS To transfer from a regular mode to the DIAG modeTo return from the DIAG mode to the normal mode To display the versionDETAILED DESCRIPTION OF DIAG MENU OTHERS Video head cleaningMaintenance CondensationVIDEO OUTPUT SIGNAL SPECIFICATIONSGENERAL VIDEO DIGITALOTHERS SpecificationsAUDIO LCD MONITORExecutive Office Broadcast & Television Systems CompanyDivision of Matsushita Electric Corporation of America One Panasonic Way 4B-7, Secaucus, NJ