Manuals / Quatech / Computer Equipment / Network Card

Quatech INTERBUS S manual The Enclosure and Specifications, System Data, $*2Ç,2Ç6670

Models: INTERBUS S

1 160

Download 160 pages 62.53 Kb

Page 16

3 The Enclosure and Specifications

3 The Enclosure and Specifications

SYSTEM DATA:

Number of function modules

Number of I/O points

Transmission medium

max. bus length

Baud rate

750-304	750-324
256	on request
4096	on request

shielded Cu-cable (5 x 0.25 mm²)

400 m

500 kBaud

INTEBUS S / Enclosure and specifications

8

:$*2Ç,2Ç6<67(0

Image 16

Quatech INTERBUS S manual The Enclosure and Specifications, System Data, $*2Ç,2Ç6670

Contents

Technical description, installation and configuration 750-132 Version Modular I/O System INTERBUS S ManualWAGO Kontakttechnik GmbH Technical Supportii General Modular I/O System INTERBUS STABLE OF CONTENTS Section 2 System Description INTERBUS S, ConfigurationSection 1 Explanations Initial Starting, Diagnosis Section 3 Digital Inputsiv Notes Modular I/O System INTERBUS SExplanation of symbols used The user is most important to usEnclosure and technical data Configuration of the fieldbus node in the masterStarting of operation and diagnostics 1 The WAGO I/O SYSTEM1 The WAGO I/O System General remark1 - Buscoupler 2 - Function modulesAssembly of the WAGO I/O System The clamping force adjusts automatically to the conductor cross section. The flat clamping face of the CAGE CLAMP spring presses the conductor against the current bar without damage. Any deformation or movement of the conductor is compensated, thus eliminating the risk of a loose connection. The contact point between conductor and CAGE CLAMP is well protected against corrosive deterioration. This connection is made fast and, furthermore, it is maintenance-free. There is no need for costly periodical examination of the connections 2 Buscoupler - INTERBUS S 2.1 Buscoupler - Hardware 2.2 Supply Voltage - Electronics 2.3 Supply Voltage - Field Side When using the supply module 750-601/602, the field supply from the bus coupler is interrupted. From that point a new power supply connection is necessary to provide DC to any additional I/O modules 2.4 Bus connection and station node address Fieldbus connectionConfiguration Interface SYSTEM DATA 3 The Enclosure and Specifications$*2Ç,2Ç6670 TECHNICAL DATA Interbus S buscoupler with extended diagnostics 750-304/000-001 4 INTERBUS S 4.1 Master Cards Scanners, Host Controllers4.2 Configuration software IBS SYS SWT IBS CMD SWTINTERBUS S / Interbus S $*2Ç,2Ç66705 Configuration of the fieldbus node in the master 5.1 Identification Code5.2 ID Code for WAGO I/O System 5.3 IBS CMD configuration software 5.3.1 CMD Software PackageINTERBUS S / Configuration 1 Automatic configuration Ill. 11 Automatic configuration$*2Ç,2Ç6670 2 Ident code Ill. 13 Insertion of the ID code and the data length INTERBUS S / Configuration$*2Ç,2Ç6670 Ill. 14 Description of user INTERBUS S / Configuration$*2Ç,2Ç6670 After all data has been entered and stored via OK, the station created with the WAGO Interbus coupler is then integrated into the fieldbus system being set up 5.4 Example of an application Ill. 19 Example of an applicationThe Interbus S station is composed as follows Table 5 Assignment of the process imageOx+y Ix+y6 Buscoupler startup and troubleshooting Status and error diagnostics 7.1 Transporting and storing conditions 7 General conditions7.2 Mechanical and climatic conditions 7.3 Class of protection and degree of protection 7.4 Electromagnetic compatibility 7.5 Power supply7.6 Certificates Digital Inputs 24 V AC/DC, 120 V AC, 230 V AC, 48 V DC PN Technical descriptionTechnical Data 50 µA typ Technical Description Counter modules$*2,26670 Technical Data $*2,26670Organization of the in- and output data $*2,26670An example $*2,26670Technical description Counter with enable input 750-404/000-001$*2,26670 Peak Time Counter 750-404/000-002 Technical data $*2,26670Organization of the in- and output data $*2,26670Frequency Counter Module, 750-404/000-003 Technical Description$*2,26670 Status CLOCKTechnical Data Measuring ErrorMeasuring Error $*2,26670$*2,26670 Functional descriptionThe,1387$7$954following$/, figures73 illustrate a process data7cycle Structure of CONTROL and STATUS byte 5$1*B6/$5$1*B6/54 CONTROL ByteStructure of Input and Output data T Dmax=Organization of the in- and output data for Interbus ByteIdentification ByteDigital Outputs Standard PN 750-501...504, 516 Technical description DigitalOutputs 750-501...504,516Technical Data Digital Outputs Standard with diagnostics PN Technical description DigitalOutputsTechnical Data Digital Outputs Solid State Relay PN Technical Description connected on the line side to protect the output modulesTechnical Data Pulsewidth Module PN Technical Description PulsewidthModuleTechnical Data Formation of on/off times Pulsewidth ModuleProcess Image Formation for Interbus Version 1 non-floating Digital Outputs Relay PN 750-512...514 Technical descriptionVersion 2 isolated outputs 750-513 Technical Data 7\SLFDOHOHFWULFDOOLIHWLPH 6ZLWFKLQJFDSDFLW\PN 750-452, 454, 750-482 Technical Description 2 Channel Analog Inputs 0-20 mA / 4-20 mA Differential InputsAnalogInputs 750-452, 454,482,484 Technical Data The numerical format The numerical format for Siemens Page PN 750-456, 750-456/000-001 Technical Description 2 Channel Analog Inputs +/- 10 V Differential InputsAnalogInputs Technical Data Analog InputsThe numerical format The numerical format for Siemens Technical description Input for PT PN 750-461, 750-461/000-002, 750-461/000-003Inputfor PT100 Technical Data Temperature C 850 100 25.5 0.1 The numerical formatThe numerical format for 750-461/000-002 The numerical format for Siemens Technical description Input for Thermocouple Modules PN 750-462, 750-469, 750-462/000-XXXInputfor thermocouple modules 750-462,469 Technical Data Warning Both inputs are referenced to a common potential not isolatedTemperature Ranges of the connectable sensors LED functionsThe numerical formats PN 750-465, 750-466, 750-486, 750-465/000-001 Technical Description 2 Channel Analog Input 0-20 mA / 4- 20 mA single endedAnalogInputs 750-465,466,486 Technical Data The numerical format Input current 0-20mA 20,5The numerical format for Siemens 750-466/000-200 or AnalogInputs 750-467,468,487,488 2 / 4 Channel Analog Inputs 0-10 V single ended PN 750-467, 468, 487Technical Description Technical Data The numerical format The numerical format for Siemens 2 Channel Analog Input 0-20mA / 4-20mA single ended PN 750-472, 750-472/000-200, 750-474, 750-474/000-200AnalogInputs 750-472 Technical descriptionNoise rejection below sampling frequency Technical DataAnalog Inputs 750-472 The numerical format 0 - 3,5The numerical format for Siemens Input current 0-20mA 2-Channel Analog Input Function clamp and variants10 V, 16 Bit, single ended 750-476Technical description $*2 , 2 2Technical Data $*2 , 2 2100 dB 40 dBerror The numerical format$*2 , 2 2 750-476Numerical format with status information $*2 , 2 2750-476/000-200 750-478/000-200$*2 , 2 2 Status bytemeaning 2 Channel Analog Outputs 0-10 V PN 750-550 Technical Description AnalogOutputs 750-550,580Technical Data The numerical formatThe numerical format for Siemens Technical Description 2 -Channel Analog Outputs 0-20 mA / 4-20 mA PN 750-552, 554AnalogOutputs 750-552, 554 Technical Data The numerical formatThe numerical format for Siemens 2 Channel Analog Outputs +/- 10 V PN Technical Description AnalogOutputsTechnical Data The numerical format 7F FFEnd module, Potential multiplication module Separation module PN750-600, 750-614, 750-616, 750-616/030-000 Technical DescriptionTechnical Data Item Number Voltage Current on contactsTechnical Data Separation moduleTechnical description Technical Description Supply modules PN750-601, 602, 609, 610, 611, 612, 613Supplymodules 750-601,602, 609,615,610,611,613 Technical Data Binary spacer module PN Technical description$*2,26670 1 2 3 4Technical Data ON 1 2 3$*2,26670 ExamplesTechnical Description SSI Encoder Interface PN 750-630, 750-630/000-001, 750-630/000-006SSIencoder Technical Data Terminal Configuration Organization of the in- and output data for Interbus WordData Word Designation $*2Ç,2Ç6670Technical Description Quadrature Encoder Interface PN 750-631, 750-631/000-001QuadratureEncoder Technical Data Operational Characteristics ConnectionType FunctionThe control byte contains the information as listed below The status byte contains the information as listed belowFunction FunctionPage Organization of the in- and output data for Interbus WordWord functionRS232C Interface, TTY Interface -20 mA Current Loop RS485C Interface PN 750-650, 750-651, 750-653, 750-650/000-001 Technical DescriptionTechnical Data Series Transmission channel Transmission rate Bit skewDescription of RS Figure 2 Data Word SignalDescription of TTY FUNCTIONM$*2 M WUDQVPLWWUHFHLY HUQGWUDQVPLWWHUUHFHLYHUDQG Description of RSControl Byte Structure of input and output dataStatus Byte Transmitting data Initialization of the moduleReceiving data Examples The module is initializedStatus Indicators Structure of the in and output data for Interbus WordWord DescriptionData exchange module PN Technical Description Dataexchange moduleTechnical Data via 2 twisted pair with differential signals 120 Ωnone, parameter configuration with software Series+$*2 Description of data exchange moduleConstant value always must be Structure of input and output dataBuffer overflow Structure of the in- and output data for Profibus from firmware WH Structure of the in- and output data for InterBus S from firmware WF Structure of the in- and output data for DeviceNet from firmware Structure of the in- and output data for DeviceNet from firmwareStructure of the in- and output data for Modbus from firmware 2 Byte special modules, Inputs Structure of the in- and output data for CanOpen from firmware WI2 Byte special modules, Outputs Mode class Structure of the in- and output data for CAL from firmware WEMode class Structure of the in- and output data for LIGHTBUS from firmware WD Ex-1 Application in Explosive Environments Ex-1.1 ForewordEx-1.2 Protective measures Ex-1.3 Classification meeting CENELEC and IECExplosive areas resulting from gases, fumes or mist Ex-1.3.2 Explosion protection groupExplosive areas subject to air-borne dust Ex-1.3.3 Unit categories Minimal ignition energy of representative types of gasesUnit ExplosionEx-1.3.4 Temperature classes Ex-1.3.5 Types of ignition protectionFurther information Ex-1.4.1 Divisions Ex-1.4 Classifications meeting the NECEx-1.4.2 Explosion protection groups Ex-1.4.3 Temperature classes Temperature classesIgnition temperature surface temperatureEx-1.5 Identification Ex-1.5.1 For Europe8 Application in Explosive Environments Identification WAGO-I/O-SYSTEM 750 Modular I/O-SystemEx-1.5.2 For America Temperature classApplication in Explosive Environments IdentificationEx-1.6 Installation regulations Danger Further InformationWAGO Kontakttechnik GmbH PostfachD-32385 Minden Hansastraße