Manuals / Quatech / Computer Equipment / Network Card

Quatech INTERBUS S manual Technical Data, Noise rejection below sampling frequency

Models: INTERBUS S

1 160

Download 160 pages 62.53 Kb

Page 93

Noise rejection below sampling frequency

Technical Data:

Item Number 750-

Number of channels

Nominal voltage

Overvoltage protection

Internal current

Input signal

Input current

Resistance

Input voltage

Resolution

Input filter

Noise rejection at sampling frequency

Noise rejection below sampling frequency

Transition frequency

Isolation

Conversion time

Bit width per channel

Configuration

Operating temperature

Wire connection

Dimensions (mm)WxHxL

Analog Inputs 750-472, 474

472	474
472/000-200	474/000-0200

2

24 V DC (-15% / +20%) via power jumper contacts

24 V max.

75 mA typ.

0-20mA

4-20mA

< 38 mA at 24 V

50Ω

non-linear/overload protection: U=1,2 V DC+160Ω*Imess

internal 16 Bit, 15 Bit via fieldbus

50Hz

<-100 dB

<-40 dB

13Hz

500 V system/power supply

80 ms typ.

16Bit: Data; optional 8Bit: Control/Status

none, optional via software parameter

0°C....+55°C

CAGE CLAMP; 0,08 to 2,5mm2

12 x 64* x 100 *from upper edge of the carrier rail

2

:$*2Ç,2Ç6<67(0

Image 93

Quatech INTERBUS S manual Technical Data, Noise rejection below sampling frequency, Analog Inputs 750-472

Contents

Modular I/O System INTERBUS S Manual Technical description, installation and configuration 750-132 VersionTechnical Support WAGO Kontakttechnik GmbHii General Modular I/O System INTERBUS SSection 2 System Description INTERBUS S, Configuration TABLE OF CONTENTSSection 1 Explanations Initial Starting, Diagnosis Section 3 Digital InputsModular I/O System INTERBUS S iv NotesThe user is most important to us Explanation of symbols usedConfiguration of the fieldbus node in the master Enclosure and technical dataStarting of operation and diagnostics 1 The WAGO I/O SYSTEMGeneral remark 1 The WAGO I/O System1 - Buscoupler 2 - Function modulesAssembly of the WAGO I/O System The clamping force adjusts automatically to the conductor cross section. The flat clamping face of the CAGE CLAMP spring presses the conductor against the current bar without damage. Any deformation or movement of the conductor is compensated, thus eliminating the risk of a loose connection. The contact point between conductor and CAGE CLAMP is well protected against corrosive deterioration. This connection is made fast and, furthermore, it is maintenance-free. There is no need for costly periodical examination of the connections 2 Buscoupler - INTERBUS S 2.1 Buscoupler - Hardware 2.2 Supply Voltage - Electronics 2.3 Supply Voltage - Field Side When using the supply module 750-601/602, the field supply from the bus coupler is interrupted. From that point a new power supply connection is necessary to provide DC to any additional I/O modules Fieldbus connection 2.4 Bus connection and station node addressConfiguration Interface 3 The Enclosure and Specifications SYSTEM DATA$*2Ç,2Ç6670 TECHNICAL DATA Interbus S buscoupler with extended diagnostics 750-304/000-001 4.1 Master Cards Scanners, Host Controllers 4 INTERBUS SIBS SYS SWT IBS CMD SWT 4.2 Configuration softwareINTERBUS S / Interbus S $*2Ç,2Ç66705.1 Identification Code 5 Configuration of the fieldbus node in the master5.2 ID Code for WAGO I/O System 5.3.1 CMD Software Package 5.3 IBS CMD configuration software1 Automatic configuration Ill. 11 Automatic configuration INTERBUS S / Configuration$*2Ç,2Ç6670 2 Ident code INTERBUS S / Configuration Ill. 13 Insertion of the ID code and the data length$*2Ç,2Ç6670 INTERBUS S / Configuration Ill. 14 Description of user$*2Ç,2Ç6670 After all data has been entered and stored via OK, the station created with the WAGO Interbus coupler is then integrated into the fieldbus system being set up Ill. 19 Example of an application 5.4 Example of an applicationThe Interbus S station is composed as follows Table 5 Assignment of the process imageIx+y Ox+y6 Buscoupler startup and troubleshooting Status and error diagnostics 7 General conditions 7.1 Transporting and storing conditions7.2 Mechanical and climatic conditions 7.3 Class of protection and degree of protection 7.5 Power supply 7.4 Electromagnetic compatibility7.6 Certificates Technical description Digital Inputs 24 V AC/DC, 120 V AC, 230 V AC, 48 V DC PNTechnical Data 50 µA typ Counter modules Technical Description$*2,26670 $*2,26670 Technical Data$*2,26670 Organization of the in- and output data$*2,26670 An exampleCounter with enable input 750-404/000-001 Technical description$*2,26670 $*2,26670 Peak Time Counter 750-404/000-002 Technical data$*2,26670 Organization of the in- and output dataTechnical Description Frequency Counter Module, 750-404/000-003$*2,26670 Status CLOCKMeasuring Error Technical DataMeasuring Error $*2,26670Functional description $*2,26670The,1387$7$954following$/, figures73 illustrate a process data7cycle 5$1*B6/$ Structure of CONTROL and STATUS byte5$1*B6/54 CONTROL ByteT Dmax= Structure of Input and Output dataByte Organization of the in- and output data for InterbusIdentification ByteDigitalOutputs 750-501...504,516 Digital Outputs Standard PN 750-501...504, 516 Technical descriptionTechnical Data DigitalOutputs Digital Outputs Standard with diagnostics PN Technical descriptionTechnical Data connected on the line side to protect the output modules Digital Outputs Solid State Relay PN Technical DescriptionTechnical Data PulsewidthModule Pulsewidth Module PN Technical DescriptionTechnical Data Pulsewidth Module Formation of on/off timesProcess Image Formation for Interbus Digital Outputs Relay PN 750-512...514 Technical description Version 1 non-floatingVersion 2 isolated outputs 750-513 Technical Data 6ZLWFKLQJFDSDFLW\ 7\SLFDOHOHFWULFDOOLIHWLPH2 Channel Analog Inputs 0-20 mA / 4-20 mA Differential Inputs PN 750-452, 454, 750-482 Technical DescriptionAnalogInputs 750-452, 454,482,484 Technical Data The numerical format The numerical format for Siemens Page 2 Channel Analog Inputs +/- 10 V Differential Inputs PN 750-456, 750-456/000-001 Technical DescriptionAnalogInputs Analog Inputs Technical DataThe numerical format The numerical format for Siemens Input for PT PN 750-461, 750-461/000-002, 750-461/000-003 Technical descriptionInputfor PT100 Technical Data The numerical format Temperature C 850 100 25.5 0.1The numerical format for 750-461/000-002 The numerical format for Siemens Input for Thermocouple Modules PN 750-462, 750-469, 750-462/000-XXX Technical descriptionInputfor thermocouple modules 750-462,469 Warning Both inputs are referenced to a common potential not isolated Technical DataLED functions Temperature Ranges of the connectable sensorsThe numerical formats 2 Channel Analog Input 0-20 mA / 4- 20 mA single ended PN 750-465, 750-466, 750-486, 750-465/000-001 Technical DescriptionAnalogInputs 750-465,466,486 Technical Data Input current 0-20mA 20,5 The numerical formatThe numerical format for Siemens 750-466/000-200 or 2 / 4 Channel Analog Inputs 0-10 V single ended PN 750-467, 468, 487 AnalogInputs 750-467,468,487,488Technical Description Technical Data The numerical format The numerical format for Siemens PN 750-472, 750-472/000-200, 750-474, 750-474/000-200 2 Channel Analog Input 0-20mA / 4-20mA single endedAnalogInputs 750-472 Technical descriptionTechnical Data Noise rejection below sampling frequencyAnalog Inputs 750-472 0 - 3,5 The numerical formatThe numerical format for Siemens Input current 0-20mA Function clamp and variants 2-Channel Analog Input10 V, 16 Bit, single ended 750-476$*2 , 2 2 Technical description$*2 , 2 2 Technical Data100 dB 40 dBThe numerical format error$*2 , 2 2 750-476$*2 , 2 2 Numerical format with status information750-476/000-200 750-478/000-200Status byte $*2 , 2 2meaning AnalogOutputs 750-550,580 2 Channel Analog Outputs 0-10 V PN 750-550 Technical DescriptionThe numerical format Technical DataThe numerical format for Siemens 2 -Channel Analog Outputs 0-20 mA / 4-20 mA PN 750-552, 554 Technical DescriptionAnalogOutputs 750-552, 554 The numerical format Technical DataThe numerical format for Siemens AnalogOutputs 2 Channel Analog Outputs +/- 10 V PN Technical DescriptionTechnical Data 7F FF The numerical formatPN750-600, 750-614, 750-616, 750-616/030-000 Technical Description End module, Potential multiplication module Separation moduleTechnical Data Item Number Voltage Current on contactsSeparation module Technical DataTechnical description Supply modules PN750-601, 602, 609, 610, 611, 612, 613 Technical DescriptionSupplymodules 750-601,602, 609,615,610,611,613 Technical Data Technical description Binary spacer module PN$*2,26670 1 2 3 4ON 1 2 3 Technical Data$*2,26670 ExamplesSSI Encoder Interface PN 750-630, 750-630/000-001, 750-630/000-006 Technical DescriptionSSIencoder Technical Data Terminal Configuration Word Organization of the in- and output data for InterbusData Word Designation $*2Ç,2Ç6670Quadrature Encoder Interface PN 750-631, 750-631/000-001 Technical DescriptionQuadratureEncoder Technical Data Connection Operational CharacteristicsType FunctionThe status byte contains the information as listed below The control byte contains the information as listed belowFunction FunctionPage Word Organization of the in- and output data for InterbusWord functionPN 750-650, 750-651, 750-653, 750-650/000-001 Technical Description RS232C Interface, TTY Interface -20 mA Current Loop RS485C InterfaceSeries Transmission channel Transmission rate Bit skew Technical DataFigure 2 Data Word Signal Description of RSFUNCTION Description of TTYWUDQVPLWWUHFHLY HUQG M$*2 MWUDQVPLWWHUUHFHLYHUDQG Description of RSStructure of input and output data Control ByteStatus Byte Initialization of the module Transmitting dataReceiving data The module is initialized ExamplesStatus Indicators Word Structure of the in and output data for InterbusWord DescriptionDataexchange module Data exchange module PN Technical Descriptionvia 2 twisted pair with differential signals 120 Ω Technical Datanone, parameter configuration with software SeriesDescription of data exchange module +$*2Structure of input and output data Constant value always must beBuffer overflow Structure of the in- and output data for Profibus from firmware WH Structure of the in- and output data for InterBus S from firmware WF Structure of the in- and output data for DeviceNet from firmware Structure of the in- and output data for DeviceNet from firmwareStructure of the in- and output data for Modbus from firmware Structure of the in- and output data for CanOpen from firmware WI 2 Byte special modules, Inputs2 Byte special modules, Outputs Structure of the in- and output data for CAL from firmware WE Mode classMode class Structure of the in- and output data for LIGHTBUS from firmware WD Ex-1.1 Foreword Ex-1 Application in Explosive EnvironmentsEx-1.2 Protective measures Ex-1.3 Classification meeting CENELEC and IECEx-1.3.2 Explosion protection group Explosive areas resulting from gases, fumes or mistExplosive areas subject to air-borne dust Minimal ignition energy of representative types of gases Ex-1.3.3 Unit categoriesUnit ExplosionEx-1.3.5 Types of ignition protection Ex-1.3.4 Temperature classesFurther information Ex-1.4 Classifications meeting the NEC Ex-1.4.1 DivisionsEx-1.4.2 Explosion protection groups Temperature classes Ex-1.4.3 Temperature classesIgnition temperature surface temperatureEx-1.5.1 For Europe Ex-1.5 Identification8 Application in Explosive Environments Identification WAGO-I/O-SYSTEM 750 Modular I/O-SystemTemperature class Ex-1.5.2 For AmericaApplication in Explosive Environments IdentificationEx-1.6 Installation regulations Further Information DangerPostfach WAGO Kontakttechnik GmbHD-32385 Minden Hansastraße