Folded Optics | Runco SC-60D, SC-50D specs

Installation

Folded Optics ➤ In rear-screen applications where space behind the projector is limited, a mirror may be used to fold the optical path, as shown in Figure 3-5.The position of the projector and mirror must be accurately set. If you are considering this type of installation, contact your dealer for assistance.

Screen

Mirror

Figure 3-5. Folded Optics

For best performance, always use “first-surface” mirrors in your

Tip rear-projection installation (as opposed to conventional, “second-surface” mirrors with the reflective surface behind a transparent substrate such as glass or acrylic).

First-surface mirrors provide a strict reflection without the “ghosting” effect seen with a second surface mirror, where a faint secondary reflection could be observed coming from the front surface of the glass.

22	Signature Cinema™ SC-50d/SC-60d Installation/Operation Manual

Image 38

Runco SC-60D, SC-50D operation manual Folded Optics

Contents

SC-50d Series SC-60d Series Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Page Table of Contents Install Anamorphic Lens Motor Operation Maintenance and TroubleshootingSpecifications External Control Xiv List of Figures List of Figures Introduction About This Manual Significance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunction Description, Features and Benefits Superwide format screen Optional Accessories Controls and Functions SC-50d/SC-60d at a Glance SC-50d/SC-60d Input Panel SC-50d/SC-60d Input Panel Analog LED RS232Dual-Link DVI-I Input Slot Digital LED DHD Controller Front Panel DHD Controller Front Panel USB DHD Controller RearPanel Display Control RS-232 To Accessory BoxComponent / Scart 3 x RCA connectors Video 1 / Video 2 / Video SC-50d/SC-60d Remote Control Units DHD Controller SC-50d/SC-60d Remote Control Unit Cursor Buttons Memory Preset ButtonsOn / OFF For more information about aspect ratios, refer to Table Hdmi 1 7 / Hdmi 2 8 / Hdmi 3 / Hdmi 4 HD 1 4 / HD 2Comp Component Scart Main Button Zoom ButtonLenss Button Installation specialist InstallationRemote Control Step Procedure For Details, Refer Quick SetupInstallation Overview Operation Installation Type Installation ConsiderationsProjector Installation Options Ambient Light SC-50d/SC-60d Lens Options and Throw Ratios Note Vertical and Horizontal Ceiling InstallationFloor Installation Position Horizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Folded Optics Audio/Video Synchronization IssuesPossible Audio Latency for Various Input Timings Input Timing Possible Audio Latency milliseconds Ventilation Requirements for Enclosure Mounting Security Screws Installing the Primary Projection LensProjector This can cause damage Remove Projector Front Installing the Optional CineWide with AutoScope Lens MotorInstall Anamorphic Lens Feet Mounting the SC-50d/SC-60d Adjusting the Projection Angle Connecting the DHD Controller to the SC-50d/SC-60d Connections to the SC-50d/SC-60d and DHD Controller DHD Connecting Source Components to the DHD Controller Hdmi Source Connections See Figure 12. Component Video Source Connections 13. Rgbhv Source Connections 14. Scart Rgbs Source Connections Composite Source Connections See Figure 15. Composite Video Source Connections Display Device to the DHD Connecting an AudioProcessor or Secondary Audio Processor Secondary Display Additional Connections to the DHD Controller Optional 17. RS-232 Control System Connection to DHD Controller 18. Connecting 12-volt Trigger Outputs AutoScope Lens Motor 19. External IR Receiver Connection Use only the AC power cord with the ferrite sleeve to 20. Ethernet Network Connection to DHD Controller Hold the Lens , Lens , Lens or Lens Turning on the PowerPrimary Lens Adjustments Focus, Zoom and Position Adjusting the Picture Orientation You must enter a passcode to access the Service menu Adjusting the Image Geometry 21. Keystone and Pincushion Distortion You must enter a passcode to access the Calibration menu Left Middle y setting also controls the Right Middle Installing and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly Carriage Plate Assembly to Lens MotorAttach Lens Mounting As close to the primary lens as possible Trigger CineWide with Configure Lens MotorAdjust the Anamorphic AutoScope Too Low Correct position Too High Anamorphic Lens Top View Geometry Verify Proper Image Working WithLamp Alignment with Using the On-Screen Menus Operation Service CUE Aspect Ratio Main MenuInput Source Select 169 to view 169 DVDs Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Hdtv programs in their Remote Aspect Ratio Control Description Key Native Picture Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Sleep Timer Sleep Timer Information SignalInformation System Calibration ISF Settings Calibration Control refer to RVR on Color Temperature Presets and Associated Color Points Copy/Paste RVR can only be used with the Power Lamp Mode setting referTo Lamp on Copied settings are not retained after a power cycle Should be used by ISF-certified technicians only ServiceTest Patterns and Their Suggested Usage Input Names Operation If a Display Error, a device-specific Operation Firmware Upgrade functions Operation Onoff CEC setting DHD Controller does not transmit Hdmi CEC control 62 and ISF Day/Night Memory Presets Regardless of the Logo LED settingRegardless of the Standby LED setting Operation Lamp Compartment Cover Retaining Screw Maintenance and TroubleshootingLamp Replacement Re-attach the Left Exhaust Side Panel to the projector Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Installing and Adjusting External Control Port ConfigurationSerial Command Syntax Serial Communications Serial Commands Input Selection Commands Picture Adjust Commands Input Position Commands Output Shift Commands Exit key Miscellaneous CommandsEnter key Using Discrete IR Codes Command Parameter Value Description Min/max Command Bits With Toggle Bit = Hex Binary Function Start RC5 Data Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller ST60MIN Opcode Value Supported? √ = Yes, = No Initiator Follower Using Hdmi CEC MessagesCEC Commands Supported by the DHD Controller Messages from the Hdmi Audio Out connector External Control SC-50d/SC-60d Projector Specifications SpecificationsSC-50d/SC-60d Projector Specifications Specifications are subject to change without notice DHD Controller Specifications DHD Controller Specifications CTUVus, FCC class B, CE, RoHS, China RoHS, Weee Dimensions SC-50d/SC-60d SC-50d/SC-60d Dimensions with CineWide with AutoScope Assembly Component Supported Signal Timings by InputSupported Timings Composite 1 Composite 2 Composite Format Resolution Frequency Rate Hz MHz KHz Rgbs 105 PAL-M Page 020-1105-00 Rev. a March