Concerning AUTO-IRIS Lenses | Sanyo VCC-6974 specs

CONCERNING AUTO-IRIS LENSES

A.I.

LENS

DC VIDEO

DC type auto-iris lens

A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens.

(Set the A.I. LENS switch to the DC position.)

VIDEO type auto-iris lens

A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is referred to as EE amplifier type lens.

ALC and LEVEL volume level controls are available on the lens for iris adjustments.

(Set the A.I. LENS switch to the VIDEO position.)

Compatible auto-iris lenses

1/3 inch Sanyo DC type lens	VIDEO type lens
VCL-CS8LY: Standard angle, f= 8 mm	Standard angle, f= 9 mm
VCL-CS4LY: Wide angle, f= 4 mm	Telephoto angle, f= 12 mm

VCL-CS2LY: Ultra-wide angle, f= 2.8 mm	Greater telephoto angle, f= 16 mm

If using a VIDEO type auto-iris lens

•Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned all the way to Av (Average).

•Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL volume on the lens casing to correct.

English 7

Image 8

Sanyo VCC-6974 instruction manual Concerning AUTO-IRIS Lenses, DC type auto-iris lens, Video type auto-iris lens

Contents

About this manual Propos de ce manuel Contents Features Pour la clientèle canadienne Information to UserFor the customers in Canada Precautions Power indicator Power Video output connector Video OUT BNC typeAlarm output terminal ALARM, C, a Parts Names Camera setup section under the cover Lens iris output connector LensMenu setting button SET Cursor button Cursor Lens mount cap If using a Video type auto-iris lens Concerning AUTO-IRIS LensesDC type auto-iris lens Video type auto-iris lens Mount type lens Mounting the LensRemove the lens mount cap from the camera Rewiring the lens cable in the lens iris plug Flange-back adjustment Coaxial cable type and maximum length ConnectionsBasic connection for monitoring or recording Connection to a multiplexer RS-485 terminal connectionsConnection to a VCR Preset will return to the zoom pan, tilt center position About the Alarm output terminalRemote controller circuit connections Using the Menu Screen Using the Cursor buttonSwitching to sub-menu screens Switching to the Main Menu screen Using the Menu Screen Language setting Then press the SET button Camera ID setting Example To set the camera ID to BN1Determining the start position for character input Changing the camera ID to a new ID Display will return to the Camera ID Setting screen External sync VBS Sync settingsInternal synchronization INT Power supply synchronization setting L L External sync setting VBS Menu Back END Lens Type setting Iris settingAI Auto Iris mode setting Adjust the Iris Level setting DC type lens only BLC setting AI/BLCMULTI BLC/EVAL 5-section photometry mode setting BLC Window Weighting screen will be displayed Weighting Returning the values to the default settings Press the Cursor l, then d or c button until EI Sense UP settingEI Electronic Iris mode setting Manual white balance MWB White Balance settingAutomatic color temperature tracking setting ATW Masking setting White BALANCE/ATWMASKING Menu Back END Push-lock white balance adjustment AWC Press and hold the SET button Manual white balance setting MWB Long exposure mode Long Electronic Shutter settingShort mode Short For Short mode For Long mode When Motion is set to ON, Long mode cannot be selected Example Motion settingIris Sense UP mode has been set. Refer to Size setting function Size Mask area setting function MaskingSensitivity setting function Sensitivity Alarm interval setting function Interval Direction setting Üü, íí, óó, ññ Size setting V vertical value is flashing, then press the Cursor c button Motion Size display table Returning to the default setting MOTION/MASKING Menu Back END Maximum Sensitivity settingThis sets the movement amplitude of subjects on the screen Zoom setting MOTION/ZOOM, Interval Interval setting Alarm Sign setting Checking the detected movements set by the Motion item Image is zoomed in when a movement is detectedCamera ID flashes on-screen when a movement is detected Active Move Differ Option settings Aperture setting AGC setting Gamma setting For FIX mode Panning Returning to the default settings OPTION/FIXI Tilt For VAR mode Zooming OPTION/VAR ZOOM, Tilt Mirror setting RS-485 setting About SW No Address settingTerminate setting Initial setting SET button Operations Using the System Controller Operations using the camera Menu screens Iris level operations Operations using the camera command Camera buttonElectronic zoom White balance and AWC-LOCK settings Setting the Sense UP and electronic shutterBacklight correction settings Menu Display 4321 Menu Display Picture is not clear TroubleshootingNo picture on the monitor screen Specifications Camera Accessories Dimensions mm Exclusions