Paging Connections see Figure, RS-232 | Sonance C4630 SE specification

C4630 SE HOME AUDIO SYSTEM

Paging Connections (see Figure 12)
Paging Connections (see Figure 12)
The C4630 SE’s PAGING connections allow connection of an audio input from a telephone
system, microphone preamp or other device to be distributed to designated Paging zones when
triggered by the CONTROL Input. (Paging must be configured in the Sonance Control Manager.)	IN	OUT
	IN	OUT
When 6 – 24VDC is present at the C4630 SE CONTROL IN terminals, all system zones set to ‘Allow		PAGE
Paging’ as configured with the Sonance Control Manager will switch to audio from the PAGE IN	Figure 12:
jack. When the control voltage drops to 0VDC, audio in the zones will switch back to the select-	Paging Connections
ed source component.
ed source component.

P A G E I N : One gold-plated mono RCA jack. Designed for use with line-level audio input from a telephone system, microphone preamp or other device to be distributed to designated Paging Zones when triggered with the Control Input. (‘Allow Paging’ must be configured in the Sonance Control Manager.)

P A G E O UT : One gold-plated mono RCA jack. Sends the Paging audio signal to other C4630 SEs in a system using multiple C4630 SE controllers.

Trigger Wire: Connect a 2-conductor non-shielded wire from the trigger voltage source on the Paging device to one C4630 SE’s CONTROL INPUT terminal (see Figure 11, on page 16), and daisy-chain to the CONTROL INPUT terminals of all other C4630 SEs in the system. (Use 20AWG wire for runs up to 500’; 18AWG wire for runs up to 1000’.)

RS-232 Connection (see Figure 13)

The C4630 SE’s RS-232 connection allows it to send or receive serial commands to or from other components. The RS-232 connection uses a female DB-9 connector with the following pinout configuration:

Pin 2 = Receive ( R X )

Pin 3 = Transmit ( T X )

Pin 5 = Ground ( G ND )

Since different serial devices have different RS-232 connection configurations, consult the documentation of the device you want to connect to the C4630 SE to determine what cable/adapter may be required.

RS-232

Pin2	Pin3	Pin5
Rx	Tx	Gnd

Figure 13:

RS-232 Terminal Pins

(Connector Side)

17

Image 17

Sonance C4630 SE Paging Connections see Figure, RS-232 Connection see Figure, RS-232 Terminal Pins Connector Side

Contents

C4630 SE Page Ance to Rain or MOISTURE. Important Safety Information Table of Contents C4630 SE Home Audio System Introduction C4630 SE FeaturesAudio Control Unpacking Box ContentsPlacement Shelf-Mounting System OverviewRack-Mounting Control Considerations C4630 SE Home Audio System Rear Panel C4630 SE Front Rear Panels Power Connections Connecting the C4630 SEReplacing the AC Fuse Audio Source Connections Wiring the Speaker Connectors Use Good Speaker WireSource Output Connections Speaker Connections Connecting a High-Power Amplifier in a Zone Line Output Fixed/Variable SwitchUsing a Multi-Channel Amplifier for Sub-Zone Expansion Zone Line Output Connections C4630 SE Using a High-Power Amplifier in a Zone IR Connections see Figure When using three or more C4630 SE Controllers, use miniPlug Y-adaptors on the IR Link jack on the Primary C4630 SE To connect to the IR Link jacks of the Secondary C4630 SEs Control Out Terminal Wiring the Control ConnectionsSync Connections Control Input/ Output Sync Connections Paging Connections see Figure RS-232 Terminal Pins Connector SideRS-232 Connection see Figure RS-232 C4630 SE Main and Numeric Keypads C4630 SE Keypad ControllersC4630 SE Main Keypad see Figure C4630 SE Numeric Keypad see , on Installing an IR Receiver into the KeypadKeypad Location Main Keypad IR Receiver Holster Keypad Backlighting Jumper Connecting the IR ReceiverC4630 SE Keypad Connections To the Keypad Keypad Ribbon Cable External Keypad Power see FigureMounting the C4630 SE Keypads Into Openings Changing the Main Keypad Source ButtonsInsert Tool C4630 SE Out-Of-The-Box Functions Optional C4630 SE IR Remote Control ALL OFF Switch Front Panel Controls and IndicatorsInstalling the Sonance Control Manager Software Sonance Control Manager Software To transfer programming to the C4630 SE Transferring System Information to the C4630 SEUpdating the Sonance Control Manager Software and Firmware Upgrading Sonance Control Manager Software Upgrading the C4630 SE Firmware Upgrade Firmware Warning Screen Device Screen Creating a New C4630 SE System Renaming C4630 SEs in a System with Multiple Units To cor rect for too low or too high a level Feedback , etc Setting Up a Zone BBE Sound Enhancement Setting Up SourcesRear-Panel BBE ON/OFF Switches General Macro Programming Notes Programming C4630 SE Keypad MacrosDevice Screen Figure Fi g u re 4 2 Z o n e 1 P ro g r a m m i n g S c re e n Building Macros Command From Library IR Commands Macro Command TypesAdding an IR Command to a Macro Macro Editor Screen Figure Programmed IR Output Port Selector Macro Editor Screen with IR Command Library SelectedDragging Commands into the Macro Window Modifying the IR Library IR Library Manager IR Library Manager Edit Tab Editing IR Commands in the User IR Library Ready to Align Remote and IR Learner Adding Function Names to the Function List Hex View Tab Internal CommandsWaveform View Tab Internal Command Window Time DelayTime Delay Macro Window Status Test RS-232 Macro Window RS-232 Command Outbound Serial ControlRS-232 Macro Editor Window with an RS-232 command string Repeat Steps Stop Macro Controlling the C4630 SE via RS-232 Inbound Serial Control Drag Commands Into BracketToggle IR Code C4630 SE Inbound Serial Protocol fixed C4630 SE Inbound Serial Commands C4630 SE Status Queries Inbound Serial Control of C4630 SEs in Multi-Unit Systems Serial Commands Simulate Button Press Commands in Multi-Unit Systems Powering K2 Keypads Wiring K2 and K1 Keypad Connections C4630 SE Extra Command Macros Expanded Control Features Programming a K2 Button to Trigger a C4630 SE Extra Command Triggering C4630 SE Extra Command Macros From the K1 and K2 Generating a System Configuration Report Getting System Configuration Information System Configuration Report Showing RS-232 Macro Commands Finding RS-232 Commands in Macros Audio Performance Specifications Problem Solution Troubleshooting Audio Infrared Control Problem Important Freight collect shipments will be refused Technical Assistance and Service Exclusions and Limitations Limited Warranty Coverage U.S.A. Only System Notes Page 33-4119 07/07