Audio | Sonance C4630 SE specs

C4630 SE HOME AUDIO SYSTEM

AUDIO (continued)
Problem	Solution
No audio in zone	a) Are speakers connected?
	b) Is zone ON?
	c) Is zone volume turned up?
	d) Check zone’s MAXIMUM VOLUME/DEFAULT VOLUME settings in Sonance Control
	Manager software.

No Paging signal in zones.	a) Be sure device’s 12V Page trigger input is connected to C4630 SE’s CONTROL
	INPUT (see page 16).
	b) Be sure Page trigger device is outputting 6 – 24V AC/DC.
	c) In an expanded system (multiple C4630 SEs) be sure the Paging audio source
	is connected to the PAGE IN jack on the primary C4630SE (see page 17).
	d) In an expanded system, be sure PAGE IN/OUT jacks are connected between
	C4630 SEs in an expanded system (see page 17).

No audio in zones driven by secondary	a) Be sure the Source Outputs on the primary C4630 SE (the one connected to
C4630 SEs in an expanded system	the source components) are connected to the Source Inputs on the secondary
	C4630 SE(s). See page 13.
	b) Check the Sonance Control Manager Volume Offset settings for sources on
	secondary C4630 SEs (should be ‘0’.) See page 30.

EXTERNAL AMPLIFIERS
Problem	Solution
Keypad or remote VOLUME UP/DOWN	a) Make sure the specific Zone FIXED/VARIABLE output switch is in the FIXED (IN)
commands change volume in all sub-	position (see page 13).
zones when using external multi-	b) Make sure the Zone’s DEFAULT and MAXIMUM VOLUMES are set at their appropriate
channel amplifier for sub-zone	maximum volume in Sonance Control Manager software to achieve proper
expansion	audio level in sub-zones. See page 29.

Keypad or remote VOLUME UP/DOWN	Make sure the specific Zone FIXED/VARIABLE output switch is in the VARIABLE (OUT)
do not adjust volume when using an	position (see page 13).
external amplifier.

53

Image 53

Sonance C4630 SE instruction manual Audio

Contents

C4630 SE Page Ance to Rain or MOISTURE. Important Safety Information Table of Contents C4630 SE Home Audio System Introduction C4630 SE FeaturesAudio Control Unpacking Box ContentsPlacement Shelf-Mounting System OverviewRack-Mounting Control Considerations C4630 SE Home Audio System Rear Panel C4630 SE Front Rear Panels Power Connections Connecting the C4630 SEReplacing the AC Fuse Audio Source Connections Wiring the Speaker Connectors Use Good Speaker WireSource Output Connections Speaker Connections Connecting a High-Power Amplifier in a Zone Line Output Fixed/Variable SwitchUsing a Multi-Channel Amplifier for Sub-Zone Expansion Zone Line Output Connections C4630 SE Using a High-Power Amplifier in a Zone IR Connections see Figure When using three or more C4630 SE Controllers, use miniPlug Y-adaptors on the IR Link jack on the Primary C4630 SE To connect to the IR Link jacks of the Secondary C4630 SEs Control Out Terminal Wiring the Control ConnectionsSync Connections Control Input/ Output Sync Connections Paging Connections see Figure RS-232 Terminal Pins Connector SideRS-232 Connection see Figure RS-232 C4630 SE Main and Numeric Keypads C4630 SE Keypad ControllersC4630 SE Main Keypad see Figure C4630 SE Numeric Keypad see , on Installing an IR Receiver into the KeypadKeypad Location Main Keypad IR Receiver Holster Keypad Backlighting Jumper Connecting the IR ReceiverC4630 SE Keypad Connections To the Keypad Keypad Ribbon Cable External Keypad Power see FigureMounting the C4630 SE Keypads Into Openings Changing the Main Keypad Source ButtonsInsert Tool C4630 SE Out-Of-The-Box Functions Optional C4630 SE IR Remote Control ALL OFF Switch Front Panel Controls and IndicatorsInstalling the Sonance Control Manager Software Sonance Control Manager Software To transfer programming to the C4630 SE Transferring System Information to the C4630 SEUpdating the Sonance Control Manager Software and Firmware Upgrading Sonance Control Manager Software Upgrading the C4630 SE Firmware Upgrade Firmware Warning Screen Device Screen Creating a New C4630 SE System Renaming C4630 SEs in a System with Multiple Units To cor rect for too low or too high a level Feedback , etc Setting Up a Zone BBE Sound Enhancement Setting Up SourcesRear-Panel BBE ON/OFF Switches General Macro Programming Notes Programming C4630 SE Keypad MacrosDevice Screen Figure Fi g u re 4 2 Z o n e 1 P ro g r a m m i n g S c re e n Building Macros Command From Library IR Commands Macro Command TypesAdding an IR Command to a Macro Macro Editor Screen Figure Programmed IR Output Port Selector Macro Editor Screen with IR Command Library SelectedDragging Commands into the Macro Window Modifying the IR Library IR Library Manager IR Library Manager Edit Tab Editing IR Commands in the User IR Library Ready to Align Remote and IR Learner Adding Function Names to the Function List Hex View Tab Internal CommandsWaveform View Tab Internal Command Window Time DelayTime Delay Macro Window Status Test RS-232 Macro Window RS-232 Command Outbound Serial ControlRS-232 Macro Editor Window with an RS-232 command string Repeat Steps Stop Macro Controlling the C4630 SE via RS-232 Inbound Serial Control Drag Commands Into BracketToggle IR Code C4630 SE Inbound Serial Protocol fixed C4630 SE Inbound Serial Commands C4630 SE Status Queries Inbound Serial Control of C4630 SEs in Multi-Unit Systems Serial Commands Simulate Button Press Commands in Multi-Unit Systems Powering K2 Keypads Wiring K2 and K1 Keypad Connections C4630 SE Extra Command Macros Expanded Control Features Programming a K2 Button to Trigger a C4630 SE Extra Command Triggering C4630 SE Extra Command Macros From the K1 and K2 Generating a System Configuration Report Getting System Configuration Information System Configuration Report Showing RS-232 Macro Commands Finding RS-232 Commands in Macros Audio Performance Specifications Problem Solution Troubleshooting Audio Infrared Control Problem Important Freight collect shipments will be refused Technical Assistance and Service Exclusions and Limitations Limited Warranty Coverage U.S.A. Only System Notes Page 33-4119 07/07