C4630 SE HOME AUDIO SYSTEM
Mounting the C4630 SE Keypads
NOTE: Do NOT mount the C4630 SE keypads in the same electrical box with AC house wiring, light switches, or any other high - voltage device or control . The keypads can share gang boxes with each other, or with other controls such as A/B speaker switches, infrared receivers and Volume Controls, if these other devices are rated as Class 2 devices according to the National Electrical Code .
1. If you are using both a Main and Numeric | Keypad, connect the |
| Ribbon Cable |
|
|
|
|
|
|
|
|
|
|
| ||
Numeric Keypad’s |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
• Connect the ribbon cable so that the wire with the red stripe |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
connects to Pin 1 on both keypads (see Figure 20). |
| PIN 14 |
|
|
|
|
|
|
|
| PIN 14 | |||||
2. Mount the keypad(s) in an appropriate |
|
|
| KEYPADMAINTOCONNECTION |
|
|
|
|
|
|
|
|
|
| KEYPADNUMBERICFORRESERVED | |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
in Keypad Location on page 19. |
| C4630 |
|
|
| C4630 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| NUMERIC |
|
|
| MAIN |
|
|
|
|
|
|
|
|
|
|
• The ribbon cable is long enough to allow a Main and Numeric | KEYPAD |
|
|
| KEYPAD |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Keypad to be mounted | double |
| • |
|
|
|
|
|
|
|
|
|
| • |
|
|
keypad can be mounted left or right. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
| PIN 1 |
|
|
|
|
|
|
|
| PIN 1 | |||||
|
|
|
|
|
|
|
|
|
|
| ||||||
|
| 1 | 2 |
|
| 1 | 2 |
|
|
|
|
| ||||
NOTE: If the ribbon cable | is connected incor rectly | the |
|
|
|
Numeric Keypad (including | its backlighting) will | not | Numeric Keypad | Main Keypad | |
function . |
|
| |||
|
| Red Stripe to Pin 1 |
| ||
|
|
|
| ||
External Keypad Power (see Figure 21) |
|
| Figure 20: |
| |
|
|
|
|
| |
If you’re connecting 6 or fewer sets of C4630 SE Main and Numeric | Keypad Ribbon Cable |
| |||
Keypads (one set in each zone) to the C4630 SE, leave the ZONE 4 – 6 |
|
|
| ||
KEYPAD POWER Switch in the INT (internal) position. No external keypad | power is |
|
| ||
required. |
|
|
| F1AL 12VDC | |
|
|
| INT |
| |
If you’re connecting more than 6 sets of C4630 SE Main and Numeric Keypads to the | ZONE |
| |||
KEYPAD POWER |
| ||||
C4630 SE, set the ZONE 4 – 6 KEYPAD POWER Switch to the EXT (external) position. Connect | EXT |
| |||
| |||||
a 12VDC 1A external power supply (Sonance PS2 Power Supply, part #91352, available |
| ||||
|
| ||||
separately) to the ZONE 4 – 6 KEYPAD EXTERNAL POWER connection to provide | adequate |
| 12 VDC | ||
| 1.0 A IN | ||||
power for the keypads in Zones 4 – 6. |
|
| – | + | |
|
|
|
| ||
See the table on page 46 for information about powering K1 and K2 programmable |
|
| |||
keypads. |
|
|
| Figure 21: |
|
|
|
|
|
| |
|
|
|
| Keypad External Power | |
|
|
|
| Connection |
|
21
