Changing the Main Keypad Source Buttons | Sonance C4630 SE specification

C4630 SE HOME AUDIO SYSTEM

Changing the Main Keypad Source Buttons

The SOURCE buttons on the C4630 SE Main Keypad are labeled to indicate the specific sources in use on the system. The keypad comes with the following buttons already installed: TUNER, CD/DVD, SAT, TV/AUX. The keypad also comes with a sheet of replacement SOURCE buttons that are labeled for a wide variety of common source components.

	To change the M ain Keypad S O U R C E buttons:
	To change the M ain Keypad S O U R C E buttons:	Insert Tool	Remove Bezel and Source Buttons
	1. If the keypad is connected, disconnect it from the	Insert Tool	Remove Bezel and Source Buttons
	C4630 SE and from the Numeric Keypad.	Into Openings
	C4630 SE and from the Numeric Keypad.

2.Use a screwdriver or similar tool to release the keypad bezel tabs (see Figure 22).

3. Remove the keypad bezel and SOURCE buttons from the keypad as shown in Figure 22.

Important: Do not touch the exposed portion of the keypad circuit board.

4.The four SOURCE buttons are a single unit. Use a razor knife or similar tool to remove the button(s) you want to replace.

	5. Use a razor knife or similar	tool	to separate	the	Figure 22:
	desired SOURCE button(s) from	the	included sheet	of
					Removing the Source Buttons
	replacement buttons.
					from the Main Keypad

6.Place all 4 of the desired Source buttons into the key-

pad bezel. The tabs on the buttons will fit-into the depressions adjacent to the openings on the back of the bezel (see Figure 23).

7.	Snap the keypad bezel back into place on the keypad.	Tabs
8.	Test all buttons for free movement. If any of the buttons are tight or hang up, carefully remove,
	realign and replace the bezel.
		Figure 23:
		Source Button Tabs

22

Image 22

Sonance C4630 SE instruction manual Changing the Main Keypad Source Buttons, Insert Tool, Into Openings

Contents

C4630 SE Page Important Safety Information Ance to Rain or MOISTURE. Table of Contents C4630 SE Home Audio System Audio C4630 SE FeaturesIntroduction Control Placement Box ContentsUnpacking Rack-Mounting System OverviewShelf-Mounting Control Considerations C4630 SE Home Audio System C4630 SE Front Rear Panels Rear Panel Replacing the AC Fuse Connecting the C4630 SEPower Connections Audio Source Connections Source Output Connections Use Good Speaker WireWiring the Speaker Connectors Speaker Connections Using a Multi-Channel Amplifier for Sub-Zone Expansion Line Output Fixed/Variable SwitchConnecting a High-Power Amplifier in a Zone Zone Line Output Connections Using a High-Power Amplifier in a Zone C4630 SE Plug Y-adaptors on the IR Link jack on the Primary C4630 SE When using three or more C4630 SE Controllers, use miniIR Connections see Figure To connect to the IR Link jacks of the Secondary C4630 SEs Sync Connections Wiring the Control ConnectionsControl Out Terminal Control Input/ Output Sync Connections RS-232 Connection see Figure RS-232 Terminal Pins Connector SidePaging Connections see Figure RS-232 C4630 SE Main Keypad see Figure C4630 SE Keypad ControllersC4630 SE Main and Numeric Keypads Keypad Location Installing an IR Receiver into the KeypadC4630 SE Numeric Keypad see , on Main Keypad IR Receiver Holster C4630 SE Keypad Connections Connecting the IR ReceiverKeypad Backlighting Jumper To the Keypad Mounting the C4630 SE Keypads External Keypad Power see FigureKeypad Ribbon Cable Insert Tool Changing the Main Keypad Source ButtonsInto Openings Optional C4630 SE IR Remote Control C4630 SE Out-Of-The-Box Functions Installing the Sonance Control Manager Software Front Panel Controls and IndicatorsALL OFF Switch Sonance Control Manager Software Updating the Sonance Control Manager Software and Firmware Transferring System Information to the C4630 SETo transfer programming to the C4630 SE Upgrading Sonance Control Manager Software Upgrade Firmware Warning Screen Upgrading the C4630 SE Firmware Creating a New C4630 SE System Device Screen Renaming C4630 SEs in a System with Multiple Units Setting Up a Zone To cor rect for too low or too high a level Feedback , etc Rear-Panel BBE ON/OFF Switches Setting Up SourcesBBE Sound Enhancement Device Screen Figure Programming C4630 SE Keypad MacrosGeneral Macro Programming Notes Building Macros Fi g u re 4 2 Z o n e 1 P ro g r a m m i n g S c re e n Adding an IR Command to a Macro Macro Command TypesCommand From Library IR Commands Macro Editor Screen Figure Dragging Commands into the Macro Window Macro Editor Screen with IR Command Library SelectedProgrammed IR Output Port Selector IR Library Manager Modifying the IR Library Editing IR Commands in the User IR Library IR Library Manager Edit Tab Adding Function Names to the Function List Ready to Align Remote and IR Learner Waveform View Tab Internal CommandsHex View Tab Time Delay Macro Window Time DelayInternal Command Window Status Test RS-232 Macro Editor Window with an RS-232 command string RS-232 Command Outbound Serial ControlRS-232 Macro Window Stop Macro Repeat Steps Toggle IR Code Drag Commands Into BracketControlling the C4630 SE via RS-232 Inbound Serial Control C4630 SE Inbound Serial Protocol fixed C4630 SE Inbound Serial Commands Inbound Serial Control of C4630 SEs in Multi-Unit Systems C4630 SE Status Queries Simulate Button Press Commands in Multi-Unit Systems Serial Commands Wiring K2 and K1 Keypad Connections Powering K2 Keypads Expanded Control Features C4630 SE Extra Command Macros Triggering C4630 SE Extra Command Macros From the K1 and K2 Programming a K2 Button to Trigger a C4630 SE Extra Command Getting System Configuration Information Generating a System Configuration Report Finding RS-232 Commands in Macros System Configuration Report Showing RS-232 Macro Commands Specifications Audio Performance Troubleshooting Problem Solution Audio Infrared Control Problem Technical Assistance and Service Important Freight collect shipments will be refused Limited Warranty Coverage U.S.A. Only Exclusions and Limitations System Notes Page 33-4119 07/07