Figure 19:C4630 SE Keypad
Controller Ports

 

 

C4630 SE HOME AUDIO SYSTEM

3. Connect the IR receiver’s 3-conductor ribbon cable to the keypad’s rear-

 

 

 

 

panel IR RECEIVER CONNECTION as shown in Figure 16. The connection

 

 

 

 

features a 3-pin removable connector similar to the ones used for the

 

 

 

FROM IR

speaker connectors. Insert the wires into the openings at the rear of the

 

 

 

 

 

 

RECEIVER

connector and secure them by tightening the screws at the top of the

 

 

 

GROUND

connector.

 

 

 

 

 

 

 

 

+12V (center)

 

 

 

 

 

• The gray wire on the ribbon cable is the DATA wire, the center wire is

 

 

 

IR DATA (white)

+12V and the remaining wire is GROUND.

 

 

 

 

 

Keypad Backlighting Jumper

 

 

 

 

 

The C4630 SE Main and Numeric Keypads have rear-panel Backlight

 

 

PIN 14

 

 

 

NUMBERICKEYPAD

 

Jumpers (Figure 17) that allow you to adjust the amount

of keypad

C4630

 

 

backlighting to suit room lighting conditions and user preference.

MAIN

 

FOR

 

KEYPAD

 

 

 

 

RESERVED

Figure 16:

Position 1 = DIM; Position 2 = BRIGHT; remove the jumper

to turn the

 

PIN 1

backlight OFF.

 

1

2

 

Connecting the IR Receiver

 

 

 

 

to the Keypad

Using needle-nose pliers, tweezers or a similar tool, carefully insert the

 

 

 

 

 

 

 

jumper in the desired position (see Figure 17). The factory default is

 

 

 

 

BRIGHT.

 

 

 

 

 

NOTE: Unless the backlight jumper is removed, the keypad backlighting

 

 

 

is always ON, even if the local zone and all zones are OFF.

1 2

1 2

1 2

C4630 SE Keypad Connections

DIM

BRIGHT

OFF

Figure 17: C4630 SE Keypad

1. In direct runs from keypad to controller, pull a length of CAT5 wire from every key-

Backlight Jumper

pad mounting location to the C4630 SE location. The maximum length of any single

 

 

 

 

 

 

CAT5 cable is 1000’.

 

 

 

2.Terminate each CAT5 cable with RJ45 connectors on each end. Follow the TIA 568B wiring standard (see Figure 18).

3.We strongly recommend testing your connections with an RJ45 network cable tester to check for cable continuity, miswiring, open connections, shorted connections or cross-pinning.

4.Connect the CAT5/RJ45 cable to the RJ45 Connection Jack on the back of the Main Keypad (see Figure 14, on page

18)and to the zone’s Keypad

Controller Port on the C4630 SE

RJ45 Connector

TIA 568B

 

Z

Z

(see Figure 19).

(Flat Side UP)

Wiring Standard

 

 

 

 

PIN

COLOR

SIGNAL

O

O

 

 

 

 

1

White/Orange

No Signal

N

N

 

 

 

 

 

2

Orange

No Signal

E

E

 

 

 

 

 

 

 

 

 

3

White/Green

No Signal

 

 

 

 

 

 

 

 

 

 

 

 

 

4

Blue

IR Data

1

2

 

 

 

 

 

 

 

 

 

5

White/Blue

Status

 

 

 

 

 

 

 

 

 

6

Green

No Signal

 

 

 

 

 

 

 

 

 

 

 

 

 

7

White/Brown

Ground

 

 

 

 

 

 

 

 

 

 

 

 

8

Brown

+12V DC

 

 

 

 

 

 

 

 

 

 

 

 

Figure 18:

Keypad Connection RJ45 Pinout

20

Page 20
Image 20
Sonance Keypad Backlighting Jumper, C4630 SE Keypad Connections, Connecting the IR Receiver, To the Keypad