6-1-5 Confirming Edit Points

You can confirm the duration between two edit points in the display.

Displaying the duration between two edit points

The following six kinds of duration can be displayed in the time data display window:

•Between IN and OUT points

•Between IN and AUDIO OUT points

•Between IN and AUDIO IN points

•Between OUT and AUDIO OUT points

•Between OUT and AUDIO IN points

•Between AUDIO IN and AUDIO OUT points

The displayed duration differs for each of the following cases:

•When two edit points are set: duration between the two points

•When only one of the edit points is set: duration between the set edit point and the current tape address

•When no edit points are set: duration of the previous edit section

To display the duration, follow the procedure below.

1 Press the RECORDER or PLAYER button to select the VTR for which you want to confirm a duration.

The button lights up.

2 Hold down any two IN, OUT, AUDIO IN, or AUDIO OUT buttons.

The duration between the points corresponding to the two buttons is displayed. The value can be negative.

 

T I M E R

D O L B Y N R

C H . C O N D

DIGITÅL

T C

 

 

 

 

S E L

 

 

 

 

 

 

G R E E N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T C

 

 

 

 

 

 

 

 

 

 

 

L O C K

 

 

 

 

 

 

 

 

 

T I M E R

D U R

V I T C P L Å Y

 

 

4 F D F 1

 

 

 

 

R E S E T

00Ó 00µ 30ß 00ƒ

 

Duration

 

 

 

Å I N

0 0 : 0 0 : 0 0 : 0 0 Å O U T

0 0 : 0 0 : 0 0 : 0 0

 

between two

 

 

 

 

 

 

 

 

 

T I M E R

I N 0 1 : 0 0 : 3 0 : 0 0 O U T 0 1 : 0 0 : 0 0 : 0 0

 

edit points

 

S E T

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T I M E R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H O L D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

o f f

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T C

T C G

 

 

 

 

T C G

 

R U N

D F / N D F

 

V I T C

 

 

 

S E L

S O U R C E

M O D E

 

 

M O D E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V I T C

 

i n t

 

 

 

p r s t

 

 

 

r e c

 

 

 

d f

 

 

o n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Displaying the duration between two edit points

6-1-6 Cuing Up and Prerolling

You can preroll the tape to a point prior to the edit start point (preroll point), or cue up the tape to any edit point.

When prerolling the tape during split editing, the VTR regards the earliest IN or AUDIO IN point as the edit start point.

Follow the procedure below to cue up or preroll the tape.

1

2

Cuing up and prerolling

1 Press the RECORDER or PLAYER button to select the VTR which you want to operate. The button lights up.

2 • To cue up the tape to an edit point

Press the IN, OUT, AUDIO IN, or AUDIO OUT button while holding down the PREROLL button.

The tape moves to the edit point corresponding to the button, then stops.

•To preroll the tape

Press the PREROLL button.

The tape is rewound to a point five seconds prior to the edit start point.

Note

When the [F1] (TIMER SEL) button in the TC menu is set to CTL, cuing up is slightly slower than in TC mode. This is to maintain the accuracy of the CTL signals.

You can set up the VTR so that priority is placed on cuing accuracy or speed. Change the VTR setting through 404. CUEUP BY TC and 405. CUEUP BY CTL in the VTR SETUP menu.

Editing 6 Chapter

Chapter 6 Editing 6-7