Sony BKDW-509, BKDW-505/506, BKDW-507, BKDW-514, BKDW-515, DVW-500/1, DVW-500P/1, DVW-A500/1, DVW-A500P/1 128

Appendix

Menu List

Item number	Item	Settable range		Function
109	FORCED EE	[0]	[on]	Specifies whether the unit automatically changes to PB/EE
	WHEN TAPE	1	off	mode whenever PB/EE is selected with the ALT/[F2] (PB/
	UNTHREAD			EE) button on the lower control panel during tape threading
				and unthreading modes and when tape is not inserted.
				0: The ALT/[F2] (PB/EE) button in the HOME menu does
				not control the PB/EE mode.
				(The E-E mode signal is output at all times.)
				1: The ALT/[F2] (PB/EE) button in the HOME menu controls
				the PB/EE mode.

111	PROGRAM	[0]	[disable]	Specifies whether program play mode is enabled or not.
	PLAY	1	enable	0: Program play mode is disabled.
				1: Program play mode is enabled.

115	PHASE LOCK IN	[0]	[off]	Specifies whether the capstan phase servo is locked during
(DVW-A500/1	VARIABLE ⋅ 3	1	on	the variable-speed mode of 3 times normal speed.
and A500P/1)				0: Capstan phase servo is not locked during the variable-
				speed mode of 3 times normal speed.
				1: Capstan phase servo is locked during the variable-speed
				mode of 3 times normal speed.

116	JOG DIAL	[0]	[TYPE 1]	Selects the tape speed (VTR command) characteristics for
	RESPONSE	1	TYPE 2	search dial rotation.
		2	TYPE 3	0: Tape speed changes linearly in a range of –1 to +1 times
				normal tape speed.
				1: Tape speed changes in a range of –3 to +3 times normal
				tape speed as shown below in TYPE 2. (Tape speed
				does not change when the search dial is within a range
				of ±1 times normal tape speed.)
				2: Tape speed changes linearly in a range of –3 to +3 times
				normal tape speed as shown below in TYPE 3.
				TYPE2		TYPE3	speed
				speed			speed
				+3 FWD		+3	FWD
				+1
				RVS	FWD	RVS	FWD
				-1	rotation		rotation
				-3		RVS	-3
				RVS		RVS
117	CONTROL	[0]	[sw selection (EXT ) ]	Specifies which control panel is enabled when the
	PANEL	1	parallel control	CONTROL PANEL switch on the system setup panel is set
	SELECTION			to ‘EXT’.
				0: Only the control panel that is connected to the external
				control connector on the connector panel is enabled.
				1: Both the control panel of this unit and the equipment
				connected to the external control connector on the
				connector panel are enabled.

A-12Appendix

Contents

Page WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture Table of Contents Page Chapter 5 Recording/Playback Editing Maintenance Appendix A-1 A-5 A-7 1-1Features 1-1-1Features of the DVW-A500/1,A500P/1, 500/1 and 500P/1 1 Chapter 1-1Features Advanced Recording and Playback Functions High-qualitydigital recording Playback compatibility with analog Betacam and Betacam SP (DVW-A500/1 1-1-2Features of the BKDW-515 Menu-drivenoperations for a variety of purposes HOME menu TC menu CUE menu DMC (Dynamic Motion Control) editing Split editing Preread editing A variety of audio editing modes Display of duration between edit points 1-2Optional Accessories Page 2-1Control Panel 2 Chapter olsContr 2-1Control Panel 2-1-1Upper Control Panel 1DISPLAY FULL/FINE button FULL: FINE: 4PHONES level control 5PB (playback) level controls 6REC (recording) level controls 7Audio level meters 8Indicator window !º INPUT SELECT button SIF (CH-1 CH-4): !¡ AUDIO INPUT/MONITOR SELECT buttons 2-1-2Lower Control Panel (Menu Operations Section) 1Menu display 2Menu buttons HOME button: TC button: CUE button: 2-1-3Lower Control Panel (Editing Operations Section) !º Numeric buttons and +/– buttons !¡ SFT (shift) button !™ RCL (recall) button !£ CLR (clear) button !¢ SET button 2-1-4Lower Control Panel (Tape Transport Section) @¢ PREROLL button @∞ EJECT button @§ STANDBY button @¶ EDIT button @• SERVO indicator @ª STOP button #º PLAY button 2-1-5Lower Control Panel (Search Operations Section) #£ VAR button #¢ JOG button #∞ SHUTTLE button Page 2-2System Set-UpPanel Connector Panel 1COMPOSITE VIDEO OUTPUT connectors (BNC) 2COMPONENT VIDEO INPUT connectors (BNC) 4REF.VIDEO INPUT connectors (BNC) and 75Ω termination switch 5BREAKER button 6AC IN connector 2-3Connector Panel !∞ REMOTE1-IN/OUT(9P) connectors (D-sub 9-pin) !§ MONITOR OUTPUT connectors (XLR-3-31) !¶ VIDEO CONTROL connector (D-sub 15-pin) !• RS-232Cconnector (D-sub 25-pin) 3-1Connecting External Equipment 3 Chapter Up Setting 3-1Connecting External Equipment 3-1-2Making Analog Connections 3-2Reference Signals for Video Output and Servo System 3-2Reference Signals for Video Output and Servo System 3-2-2Reference Signal for the Servo System 3-2-3Reference Signals Connections Reference signal connections For recording signals from a switcher or signal generator For recording signals from a VTR For playback 3-3Handling Cassettes 3-3Handling Cassettes Removing slack in the tape Preventing double cassette inserting Ejecting the cassette 3-3-3Preventing Accidental Erasure 4-1Registering and Storing Menu Settings Settings uMen 4 Chapter 4-1Registering and Storing Menu Settings 4-1-2Changing Menu Settings To return to the first page Changing menu settings using the cursor control buttons To cancel the registration of all new items 4,5 To cancel a currently registered item To scroll the menu faster 4-1-4VTR Memory Bank Function Storing the current VTR menu settings to a VTR memory bank 2 6,7 To cancel the storage operation Recalling menu settings from a VTR memory bank 2 5,6 To cancel the recalling operation 4-1-5IC Memory Card Function 3,4,5 To eject the IC memory card Formatting an IC memory card To cancel formatting Storing the contents of the VTR memory banks to an IC memory card 2 7,8 6 3 91 4,5 To store the current VTR menu settings only To store all VTR memory banks Storing cue point lists to an IC memory card 2 3 6,7 To return to the SET UP menu Recalling the contents of an IC memory card 5 3 91 4,6 To change the current VTR menu settings To replace all VTR memory bank contents with IC memory card data Recalling a cue point list in an IC memory card 23 6,7 4-1-6Adding Titles to the Data 4 5 1,3 To enter a space If you enter a wrong character To cancel the procedure to start again 4-1-7Details on VTR Memory Bank and IC Memory Card Functions Data that can be stored to/recalled from a VTR memory bank or IC memory card Data that cannot be stored to a VTR memory bank or an IC memory card 4-1-8IC Memory Card Data Compatibility Among the DVW 4-2HOME Menu 4-2-1Setting the Preread Function (PRE READ) 4-2-2Simultaneous Playback During Recording (CONFI) 4-2-3Selecting the Edit Mode and Edit Channel (ASSEMBLE to 4-2-4Setting Record Inhibit Mode (REC INH) all: crash: video 4-2-5Selecting the Monitor Mode (PB/EE) 4-2-7Selecting the Capstan Servo Lock Mode (CAP LOCK) 4-2-10Selecting Program Playback (P-PLAY) 4-3TC Menu 4-3-1Setting the Time Data (TIMER SEL/RESET/SET/HOLD) Setting time code To cancel entered value 4-3-3Setting the Time Code Generator (TCG SOURCE/MODE) 4-3-4Selecting the Time Code Running Mode (RUN MODE) 4-3-7Selecting CTL Display Mode (TAPE TIMER) 1Types of time data 2Drop frame mark of the time code reader (DVW-A500/1and 500/1 only) 3Drop frame mark of the time code generator (DVW-A500/1and 500/1 only) 4Field mark of the VITC data ” (blank): Page 4-3-10Setting the VITC Insertion Line (VITC POS-1/POS-2) 4-4CUE Menu 4-4CUE Menu 4-4-1Selecting a Multi-CueMode PAGE mode Display Selecting a page To select the cue number directly by numeric buttons Registering cue points by the numeric buttons To select the cue number directly by the numeric buttons To modify current cue point data 4-4-3Erasing Cue Point Data To erase all cue point data 4-4-4Prerolling to a Cue Point Prerolling to a cue point 4-4-5Changing a Cue Point Into an Edit Point To change an edit point into an IN point To change an edit point into an OUT point To change an edit point into an AUDIO IN point To change an edit point into an AUDIO OUT point 4-5PF1 Menu (Factory Settings) 4-5PF1 Menu (Factory Settings) 4-5-1Selecting the Input Video Signal (VIDEO IN) sif: cmpst: y-r/b: Adjusting the output level prst: Numerical value: 0 to B50H Adjustable range: –3to +3 (dB) Adjusting the chroma output level PF2 Menu (Factory Settings) 4-6-1Selecting the Audio Input Signal (A-INALL to A-INCH4) 4-47 -SET7SETUP MenuUP Menu Selecting remote operation mode When the [F8] (REMOTE 9-PIN)button is set to on When the [F9] (REMOTE 50-PIN)button is set to on Setting the test signal 4-7SET UP Menu 4-7-1VTR SETUP Menu To activate the VTR SETUP menu Scrolling items in the VTR SETUP menu To search the menu by category 2,3 To activate the multi-loopfunction 4-7-2PANEL SETUP Menu To activate the PANEL SETUP menu Disabling the upper and lower control panel buttons Setting the keyboard sound high: low: Setting the alarm Page 5-1Preparing for Recording Recor 5 Chapter ybackding/Pla 5-1Preparing for Recording 5-1-2Selecting Audio Signals Selecting the audio input signals Selecting audio signals to be monitored To adjust the audio output level of the PHONES jack To adjust the audio output level of the MONITOR OUTPUT connectors 5-1-3Adjusting the Audio Recording Level Adjusting the recording level Recording with the reference level Recording with the specific recording level 5-1-4Monitoring Simultaneous Playback of Video and Audio Signals Being Recorded Monitoring signals being recorded Monitoring previously recorded video and audio signals while recording 5-2Recording Preparing for Playback 5-4Playback 5-4Playback 5-4-2Variable Speed Playback in Jog/Shuttle/Variable Modes Variable mode: Jog mode playback 1,2,3 3 1,2,3 To return to normal-speedplayback To alternate between normal-speedplayback and shuttle mode playback Variable mode playback 3 2,3 To alternate between normal-speedplayback and variable mode playback 5-4-3Capstan Override Playback 5-4-4DMC Playback Overview of DMC playback 1,2 1(A) Storing playback speeds in memory To confirm and change the stored speed To set the initial speed to normal speed Notes on the p indicator and the MEMORY indicator Performing DMC playback 1,2 To start playback at the on-aircue from the on-airstart point To start playback immediately after prerolling To stop the tape during DMC playback To exit DMC playback mode 5-4-5Program Playback Before performing program playback Performing program playback Page 6-1Basic Automatic Editing 6 Chapter 6-1Basic Automatic Editing 6-1-2Setting Switches and Menus 6-1-3Selecting the Edit Mode Assemble mode: Insert mode: 6-1-4Setting Edit Points Positioning and setting edit points To delete entered data About automatic edit point setting Split editing Positioning and setting edit points About automatic split edit point setting When the AUDIO IN point is not set for insert editing of audio only Using a VTR without the split editing function 6-1-5Confirming Edit Points Displaying the duration between two edit points 6-1-6Cuing Up and Prerolling Changing the preroll time 6-1-7Previewing To stop previewing To rewind the tape to the preroll point To rewind the tape to the edit point Monitoring signals during previewing 6-1-8Modifying Edit Points Deleting edit points Moving an edit point position one frame at a time 2,3 Moving an edit point position with the numeric buttons To cancel the entered value 6-1-9Performing Automatic Editing Monitoring signals during editing Performing automatic editing To stop automatic editing To confirm the results of the editing Modifying edit points for automatic editing later Advanced Automatic Editing If the p indicator goes off before the tape passes the OUT point To exit DMC editing mode Performing DMC editing To confirm the results of DMC editing Notes on controlling VTRs with DT 2,4 For even quicker editing 6-2-3Performing Consecutive Editing To stop consecutive editing 6-2-4Performing Preread Editing 6-3Manual Editing Page 7-1Head Cleaning Maintenance 7 Chapter Moisture Condensation Specifications Appendix Specifications Analog composite input (with optional BKDW- 505/506) to analog composite output Analog audio (Cue track) Digital audio (CH-1to CH-4) Analog input to output Audio DVW-A500P Processor adjustment range Input connectors Output connectors Remote connectors Accessories supplied Optional accessories Glossary Glossary Menu List Menu List Items Related to VTR Operations (000s) Page Items Related to Operation Panels (100s) Page Page Page Items Related to Remote Interface (200s) Items Related to Editing (300s) Page Page Page Items Related to Prerolling (400s) Items Related to Recording Protection (500s) Items Related to the Time Code Generator (600s) Page Page Items Related to the Video Control (700s) Page Page Page Page Page Page Items Related to the Audio Control (800s) Page Page Items Related to Digital Processing (900s) Page Page Items Set by Switches on Models DVW-A500, A-500P,500, and 500P (Ks) Page Page Page Page Page Index Index Index P, Q V, W, X, Y, Z Function Button List (Factory Settings)