Sony DASK-S704 58

Compiling

5Press the F4 key. “Complete?” flashes.

O O

	[(03)Church A ]		Complete ?
SAMPLE	[1:C12	]	No	Enter

14To finish compiling, press the F4 key. The following display appears.


	Rehearsal		Save Fs data to
	Sampling
			MS [xxxxxxxx]?

	Compile		or Change MS and Press F2
	Change MS

SAMPLE

Change MS

Exit

Enter

•To change the reverb program name or the assigned graphics, press the F3 key (No) in place of the F4 key. The reverb program name setting menu in step 12 returns.

15Assign the Memory Stick in which you want to store the compiled reverb program.

Select the Memory Stick in use or another Memory Stick.

Name of the Memory Stick in use


	Rehearsal		Save Fs data to
	Sampling
			MS	[xxxxxxxx]?
	Compile
			or Change MS and Press F2
	Change MS

SAMPLE

Change MS

Exit

Enter

To store in the Memory Stick in use

Press the F4 key. The memory list of the Memory Stick is displayed.

Proceed to step 16.

To store in another Memory Stick

1Change the Memory Stick to another one.

2Press the F2 key.

“Checking MS Please wait for a few minutes.” is displayed, then the display in step 15 appears.

3Press the F4 key.

The memory list of the Memory Stick is displayed. Proceed to step 16.

Notes

•If the capacity of the Memory Stick in use is not sufficient, “No Space on MS[xxxxxxxx] Delete files or Change MS and Presss F2” is displayed. Delete unnecessary files in the Memory Stick or change the Memory Stick.

For details, see “If the memory capacity of the Memory Stick is not sufficient” on page 16.

•If you insert a new Memory Stick, “This MS is new Press F4 and enter name of MS” is displayed. Name the Memory Stick.

For details, see “To name a new Memory Stick” on page 17.

22(GB)

Contents

取扱説明書 Page Page Page サンプリングの基本手順ブロック図サンプリング時の内部ブロック図コンパイル時の内部ブロック図サンプリングの接続例アナログ接続の例デジタル接続の例 DASK-S704の起動 DRE-S777の電源を入れるときに起動する DRE-S777 Page サンプリングリバーブソフトウェアの「GoToSample」から起動する GoToSample Page リハーサル（Rehearsal）サンプリング（Sampling） Sampling Page Page Page Page Page コンパイル（Compile） Compile Page Page Page Page Page 音源のグラフィックを割り当てる独自のインパルスレスポンスをコンパイルするメモリースティックの交換（Change MS） Change MS セットアップ画面（SETUP） SETUP SETUP画面の操作 SETUP画面で設定・調整可能な項目 SETUP Page リバーブプログラムの再生リバーブモードとサンプリング時の配置 Page エラーメッセージ本機の性能を保持するために（使用上のご注意）メモリースティックの使用上のご注意 CD-ROMの取り扱い上のご注意 CD-ROM メモリースティックの取り扱い上のご注意 English Table of Contents Overview Basic Procedures of Sampling Block Diagrams Connection Examples for Sampling Connection Examples for Sampling Digital Connection Starting the DASK-S704 Starting the DASK-S704 Removing the Memory Stick To use the Memory Stick again Starting the DASK-S704Using the “GoToSample” Function of the Sampling Reverb Software Initial display of the DASK-S704 Menu section Current setttings Display mode Function key indicator Rehearsal Sampling To store in the Memory Stick in use To store in another Memory Stick To set a new memory label To modify an existing memory label To input a character: To insert a space: To delete an input character: If the memory capacity of the Memory Stick is not sufficient To change to another Memory Stick To delete unnecessary data To name a new Memory Stick Compiling Page Compiling Page Page Page Assigning the Reverb Source Graphic Reverb source graphics supplied with the DASK-S704 To assign your particular reverb source graphic Compiling Your Particular Impulse Response Changing the Memory Stick SETUP Display SETUP Display The Items Available in the SETUP Display Page Page Reproducing the Reverb Program Reverb Modes and Arrangement during Sampling Reverb Modes and Arrangement during Sampling To obtain the “Stereo in Stereo out” effect Error Messages Precautions