Menus 7 Chapter

 

 

 

Menu items in the 700s, relating to video control

 

 

 

 

 

 

Item

Item name

Settings

number

 

 

 

 

 

 

 

 

 

 

 

 

 

731

WIDE MODE

Specify whether to record and play back with the addition of wide picture

 

 

 

 

 

information.

 

Sub-item

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

INPUT

 

Specify whether to save wide picture information on a disc during recording.

 

 

 

 

 

auto: Automatically record wide picture information when it is detected in the

 

 

 

 

 

 

selected input video signal.

 

 

 

 

 

on: Always record wide picture information.

 

 

 

 

 

off: Do not record wide picture information.

 

 

 

 

 

 

 

 

2

 

OUTPUT

 

Specify whether to add wide picture information to the output signal during

 

 

 

 

 

MPEG IMX playback.

 

 

 

 

 

thru (through): Output the video signals of the disc being played back

 

 

 

 

 

 

without adding wide picture information.

 

 

 

 

 

auto: When wide picture information is detected on the disc being played

 

 

 

 

 

 

back, add wide picture information to the output video signals.

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes

 

 

 

 

 

•

To add wide picture information to the output signal, it is necessary, in

 

 

 

 

 

 

addition to setting this item to “thru,” to operate extended menu item 703 to

 

 

 

 

 

 

set line 20 (in 525 line mode) to “thru” or set line 23 (in 625 line mode) to

 

 

 

 

 

 

“thru.”

 

 

 

 

 

•

In 525 line mode, wide picture information may not be output if VITC signal

 

 

 

 

 

 

insertion position is set to line 20 in extended menu item 601 or 602.

 

 

 

 

 

 

 

 

 

Menu items in the 800s, relating to audio control

 

 

 

 

 

 

Item number

Item name

 

 

 

Settings

 

 

 

 

 

 

 

802

 

DIGITAL AUDIO MUTING IN

 

 

 

Set the audio muting conditions during shuttle playback.

 

 

SHUTTLE MODE

 

 

 

off: Not muted.

 

 

 

 

 

 

 

on: Muted.

 

 

 

 

 

 

 

807

 

AUDIO OUTPUT PHASE

 

 

 

Set the output timing of digital audio playback signals (SDI, AES/EBU

 

 

 

 

 

 

 

only), with 80H as a reference position. Output timing is earlier for

 

 

 

 

 

 

 

values smaller than 80H and later for values greater than 80H. (80H,

 

 

 

 

 

 

 

128 samples = approx. 2.7 ms, 80H, 1 sample = approx. 20 μs)

 

 

 

 

 

 

 

0 (0 (HEX))... 80 (80 (HEX))... FF (FF (HEX)): Values can be set in this

 

 

 

 

 

 

 

 

range.

 

 

 

 

 

 

 

808

 

INTERNAL AUDIO SIGNAL

 

 

 

Select the operation of the internal audio test signal generator.

 

 

GENERATOR

 

 

 

silnc (silence): Silent signal.

 

 

 

 

 

 

 

1kHz (1kHz sine): 1 kHz, –20 dB FS sine wave signal.

 

 

 

 

 

 

 

When you select SG as the audio input in the input selection section of

 

 

 

 

 

 

 

the control panel, the audio test signal generated by the internal audio

 

 

 

 

 

 

 

test signal generator is input.

 

 

 

 

 

 

 

815

 

AUDIO SAMPLING RATE

 

 

 

Select the mode of operation of the sampling rate converter for AES/

 

 

CONVERTER

 

 

 

EBU input to channels 1 to 4.

 

 

 

 

 

 

 

off: Do not operate.

 

 

 

 

 

 

 

on: Operate.

 

 

 

 

820

 

AUDIO OUTPUT CH1/CH2 SELECT

Select the signals to be output from the AUDIO OUT 1/3 and AUDIO

 

 

 

 

 

 

 

OUT 2/4 connectors.

 

 

 

 

 

 

 

line (line out): Output the audio channel signals selected with item 824

 

 

 

 

 

 

 

 

“just as they are” from the AUDIO OUT 1/3 and 2/4 connectors.

 

 

 

 

 

 

 

moni (monitor out): Output the monitor audio L-channel (CH-1) and

 

 

 

 

 

 

 

monitor audio R-channel (CH-2) signals from the AUDIO OUT 1/3 and

 

 

 

 

 

 

 

AUDIO OUT 2/4 connectors, respectively.

 

 

 

 

 

 

 

 

 

106 7-3 Extended Menu