Display in video panel and on external monitor

Cursor indicating the currently selected sub-item

ITEM-703

BLANK LINE SELECT

 

* ALL LINE

-

---

LINE 12

-

blnk

 

- - - -

 

Display in time data display

Sub-item number (flashing while changing)

4 With the SHUTTLE button held down, rotate the jog dial or shuttle dial to change the setting.

The displays in the video panel, on an external monitor, and in the time data display section change as shown below when you hold down the SHUTTLE button. In the time data display section, the currently selected setting value flashes to indicate that you can change it to another value.

Display in video panel and on external monitor

Setting value

ITEM-001

PREROLL TIME

5 sec

Display in time data display

Setting value (flashing while changing)

5 Press the SET button.

This saves the new setting value, and the menu display disappears from the video panel, the external monitor, and the time data display section.

To abandon making a change

Press the MENU button before pressing the SET button.

The menu display disappears from the video panel, the external monitor, and the time data display section without the new setting value being saved.

Resetting the menu settings to their factory default values

To reset the current active menu settings to their factory default values, proceed as follows.

 

 

 

 

 

1

 

3

2

 

 

 

 

 

TC

COUNTER

 

SUB

THUMB

SHUTTLE

JOG

 

KEY INHI

 

 

SHIFT

 

 

NETWORK

ON

INT

PRESET

F-RUN SEL

HOLD

CLIP

NAIL

 

 

 

 

 

 

 

LOCAL

 

EXT

 

 

 

 

 

 

 

 

ACCESS

REMOTE

OFF

RP188

REGEN

R-RUN

 

 

CLIP

ESSENCE

 

 

ALL/CH-1

CH-2

CH-3

CH-4

 

 

MENU

MARK

 

 

METER

MONITOR

 

 

 

 

VARIABLE

 

 

 

 

 

MENU

SET

RESET

 

REC

 

 

 

 

 

SEL

SEL

 

PRESET

 

 

 

 

 

 

 

 

 

 

 

PB

 

 

 

 

 

 

L/ST/R

SYSTEM

S.SEL

 

 

 

 

 

AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU

MARK1

 

PREV

PLAY

NEXT

STOP

 

REC

 

 

 

 

 

 

 

 

 

 

 

 

IN

 

OUT

 

TOP

F REV

F FWD

END

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MARK2

 

1 Press the MENU button.

The menu appears in the video panel, on an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input, and in the time data display section.

2 Press the RESET button.

The message “INITIALIZE ALL ITEMS TO FACTORY PRESET VALUES?” appears in the video panel and on the external monitor.

The message “Init setup?” appears in the time data display.

To abandon operations and return to the setup menu display

Press the RESET button again.

3 Press the SET button.

The menu settings are reset to their factory default settings.

Switching between 525(U) line, 525(J) line and 625 line modes (menu item 013)

To switch between 525(U) line, 525(J) line and 625 line operation modes, proceed as follows.

1 Press the MENU button.

2 Turn the jog dial or shuttle dial to display menu item 013 in the time data display.

Menus 7 Chapter

7-2 Basic Setup Menu 95