5-2-3 Trimming Sub Clips

SET button

THUMBNAIL button

 

 

 

 

 

 

 

 

 

 

SHIFT button

 

 

 

 

 

 

 

 

 

 

 

 

RESET button

 

 

 

 

 

TC

COUNTER

 

SUB

THUMB

SHUTTLE

JOG

 

 

KEY INHI

 

 

 

SHIFT

 

 

NETWORK

ON

 

INT

PRESET

F-RUN SEL

HOLD

CLIP

NAIL

 

 

 

 

 

 

 

 

LOCAL

 

 

EXT

 

 

 

 

 

 

 

 

ACCESS

REMOTE

OFF

 

RP188

REGEN

R-RUN

 

 

CLIP

ESSENCE

 

 

ALL/CH-1

CH-2

CH-3

CH-4

 

 

MENU

MARK

 

 

METER

MONITOR

 

 

 

 

VARIABLE

 

 

 

 

 

 

MENU

SET

RESET

 

REC

 

 

 

 

 

 

SEL

SEL

 

PRESET

 

 

 

 

 

 

 

 

 

 

 

 

PB

 

 

 

 

 

 

 

L/ST/R

SYSTEM

S.SEL

 

 

 

 

 

 

AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU

MARK1

 

PREV

PLAY

 

NEXT

STOP

 

REC

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

 

OUT

 

TOP

F REV

F FWD

END

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MARK2

 

Jog dial

g/OUT button

F/f buttons

G/IN button

NEXT button

PREV button

1 Carry out steps 1 to 4 of 5-2-2 “Reordering Sub Clips” to select a sub clip and display the sub clip operation menu.

2 Use the F or f button to select TRIM, and then press the SET button.

The first frame of the selected sub clip appears. The first and last frames are set as provisional In and Out points, and the IN and OUT indicators light.

In this state, you can play back and search the entire disc.

To cancel the trim and return to the previous screen

With the SHIFT button held down, press the SET button.

3 Play back and search the disc to find scenes to set new In and Out points.

4 At the scene where you want to set a new In or Out point, hold down the G/IN button (to change the In point) or the g/OUT button (to change the Out point) and press the SET button.

Depending on the button that you pressed, a new In or Out point is set.

To change both the In and Out points

Carry out steps 3 and 4 for both the In and Out points.

To reset the In or Out point

With the G/IN button or g/OUT button held down, press the RESET button. The In or Out point is restored to the value it had before the sub clip trim screen opened.

To cue up the In or Out point

With the G/IN button held down, press the PREV button. Or with the the g/OUT button held down, press the NEXT button.

Note Note

You can escape from the sub clip trim screen to full- screen display without executing a trim if you press the THUMBNAIL button.

5 Once you have set the new In point or Out point, hold down the SHIFT button and press the SET button.

The trim is executed, and you return to the sub clip thumbnail display.

To cancel the trim

Reset the In or Out point to the value it had before you entered the sub clip trim screen, and then hold down the SHIFT button and press the SET button.

6 Save the current clip list to disc.

See 5-2-6 “Saving the Current Clip List to Disc” (page 66).

Selection Scene 5 Chapter

5-2 Creating Clip Lists

65