Parts of Functions and Names 2 Chapter

cREMOTE (remote control signal) connector (D-

sub 9-pin)

To control the PDW-R1 from a controller or VTR supporting the RS-422A Sony 9-pin VTR protocol, connect the device to this connector.

dREF VIDEO IN (reference video signal input) connector (BNC type)

Input a reference video signal.

e (network) connector (RJ-45 type)

This is a 10Base-T/100Base-TX connector for network connection.

To transfer files between an external device and the PDW- R1, connect a network cable to this connector and the external device.

Caution

For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions in this manual when making connections.

ATTENTION

Par mesure de sécurité, ne raccordez pas le connecteur pour le câblage de périphériques pouvant avoir une tension excessive à ce port. Suivez les instructions pour ce port.

ACHTUNG

Aus Sicherheitsgründen nicht mit einem Peripheriegerät- Anschluss verbinden, der zu starke Spannung für diese Buchse haben könnte. Folgen Sie den Anweisungen für diese Buchse.

fS400 (i.LINK) connector (6-pin, IEEE1394 compliant)

Connect a DV device, computer, or similar, using an i.LINK cable. To prevent the connector from coming loose, we recommend that you secure the cable in the cable clamp as shown in the following figure.

To i.LINK (IEEE 1394)

Cable clamp

 

 

 

 

connector of DV device or PC

 

 

 

 

 

REMOTE

REF VIDE

 

DC OUT 12V

 

 

i.LINK cable

 

 

 

(not supplied)

S400 IN

VIDEO

 

 

OUT1

OUT2(SUPER

When the unit is shipped from the factory, the audio output signal is set to 16 bit/48 kHz/2ch mode. You can change the audio mode and output channel settings with extended

menu item 831 “DV OUT AUDIO MODE” and extended menu item 828 “SDI/DV AUDIO OUTPUT SELECT.”

See 7-3-2 “Extended Menu Operations” (page 108) for more information about how to make these settings.

Notes

•If video or audio signals from an external device

connected with the S400 (i.LINK) connector are not output, disconnect the i.LINK cable and connect it again, pushing it straight in.

•When the PDW-R1 is connected to a device with a 6-pin i.LINK connector by an i.LINK cable, before unplugging the i.LINK cable, first power off the device and disconnect the power plug from the outlet. If the i.LINK cable is unplugged with the device power plug still connected, a current from an excessive voltage (8 to 40 V) output from the i.LINK connector of the device flows into the PDW-R1. This may cause a failure of the PDW-R1.

•When connecting the PDW-R1 to a device with a 6-pin i.LINK connector, connect to the 6-pin i.LINK connector of the other device first.

•Except in playback mode (jog and shuttle modes, etc.), if you are monitoring the audio signal output from this connector on another device, the audio signal may sound differently from the audio signal played back on the PDW-R1.

1 Digital audio signal inputs/outputs

1 DIGITAL AUDIO (AES/EBU) IN 1/2, 3/4 connectors

2 DIGITAL AUDIO (AES/EBU) OUT 1/2, 3/4 connectors

DIGITAL AUDIO (AES/EBU)

IN

1/2

3/4 OUT

1/2

3/4

aDIGITAL AUDIO (AES/EBU) IN (digital audio input) 1/2, 3/4 connectors (BNC type)

These input AES/EBU format digital audio signals. The left connector (1/2) corresponds to audio channels 1 and 2, and the right connector (3/4) corresponds to audio channels 3 and 4.

bDIGITAL AUDIO (AES/EBU) OUT (digital audio output) 1/2, 3/4 connectors (BNC type)

These output AES/EBU format digital audio signals. When the unit is shipped from the factory, the 1/2 connector is set to audio channel 1/2, and the 3/4 connector is set to audio channel 3/4. You can change these settings with extended menu item 827 “AES/EBU AUDIO OUTPUT SELECT.”

22 2-4 Connectors