7-4 Maintenance Menu

7-4-1 Items in the Maintenance Menu

The following tables show the items in the maintenance menu.

•Item names are the names which appear in the video panel, and on an external monitor to which the output of the VIDEO OUT 2 (SUPER)/SDI OUT (SUPER) connector is input.

•The values in the Settings columns are the values which appear in the time data display section. (The values may

appear in a different format in the video panel and on an external monitor. In this case, the video panel values are shown in parentheses.) Underlined values are the factory defaults.

For information about the DRIVE MAINTENANCE, ADJUST, CHECK, BATTERY CONFIG and SERVICE SUPPORT items, refer to the Maintenance Manual.

Menus 7 Chapter

 

AUDIO CONFIG: items relating to audio control

 

 

 

Item

Setting

 

 

 

METR HEAD ROOM

Select the audio reference level (headroom).

 

–12dB,–16dB, –18dB, –20dB (525(U)/525(J) line modes)

 

–12dB, –16dB, –18dB, –20dB, EBUL (625 line mode)

 

 

 

DATA LENGTH

When “IMX50,” “IMX40,” or “IMX30” is selected in setup menu item 031, this selects the

 

audio quantization bit count and number of recording channels.

 

16⋅8 (16bit ⋅ 8ch): 16 bits ⋅ 8 channels

 

24⋅4 (24bit ⋅ 4ch): 24 bits ⋅ 4 channels

 

 

 

 

 

Note

item 031 is set to “DVCAM,” the setting is automatically fixed at 16 bits ⋅ 4 channels.

 

When

 

 

 

NON-AUDIO INPUT

Select whether to handle digital audio signals as non-audio signals during recording.

 

Audio (audio): Handle as audio signals.

Sub-item

data: Handle as non-audio signals.

 

tr1/tr2

 

 

 

 

 

 

 

 

 

tr3/tr4

 

 

 

 

 

 

 

 

 

tr5/tr6

 

 

 

 

 

 

 

 

 

tr7/tr8

 

 

 

 

 

 

 

INPUT LEVEL

Set the upper limit for the signal level input to audio channels 1/3 or 2/4.

 

+4dB, 0dB, –3dB, –6dB (525(U)/525(J) line modes)

Sub-item

+4dB, 0dB, –3dB, –6dB, EBUL (625 line mode)

 

CH1/CH3

 

 

 

 

 

 

 

 

 

CH2/CH4

 

 

 

 

 

 

 

OUTPUT LEVEL

Set the reference level for audio output signals.

 

+4dB, 0dB, –3dB, –6dB (525(U)/525(J) line modes)

 

+4dB, 0dB, –3dB, –6dB, EBUL (625 line mode)

 

 

 

 

NETWORK CONFIG: items relating to network settings

 

 

 

Item

Setting

 

 

 

 

DHCP

Set whether to assign an IP address automatically with the DHCP server.

 

 

DISABLE: Do not assign automatically.

 

 

ENABLE: Assign automatically.

 

 

 

 

IP ADDRESS PRESET

Set IP address.

 

 

192.168.001.010

 

 

 

 

 

Note

 

 

 

When

DHCP is set to “ENABLE,” it is not possible to set the IP address.

 

 

 

 

 

 

112 7-4 Maintenance Menu