Far end camera control Fecc | TANDBERG 5000 manual

VISION 5000 Videoconferencing System General use

Far end camera control (FECC)

FAR END

Press the CAMERA key until the ‘FarEndCamera’ on-screen indicator is displayed.

For this feature to operate the remote side must support ‘Far end camera control’ (H.281).

Whilst activated you will be able to control the remote side’s camera (pan/tilt/zoom/focus) and presets. To control the remote camera use the keys below:

UP
LEFT OK RIGHT	for pan/tilt, and	ZOOM	for zooming,	FOCUS	for focusing.
	for pan/tilt, and		for zooming,		for focusing.
DOWN
Remote presets can be activated by pressing the keys				P1	P2 P3 P4 or the keys 0-9 to activate presets P0-
P9.
Selection of remote videosources is achieved by pressing					VIDEO
Selection of remote videosources is achieved by pressing					SOURCE when in FarEndCamera mode and selecting

the desired video source from the menu.

Note

You cannot store presets on the remote side and some units do not support ten presets.

To prevent others from controlling your camera,— select ‘Far End Camera Control:Off’ in ‘Utilities’ ‘Advanced use’.

Page 35

Image 35

TANDBERG 5000 user manual Far end camera control Fecc

Contents

N D B E R G Vision 5000 Videoconferencing System Lysaker, Norway, Tel +47 67 125 125, Fax +47 67 125 Environmental Issues Vision 5000 Videoconferencing System Operator Safety Summary Contents Appendices Index Vision 5000 Videoconferencing System Advanced useEthernet Functionality Peripheral Equipment Introduction How to use this guide Main menu Menu structureVision 5000 on-screen menu structure is shown below Right keys to move through the menu structure At a glance the Vision 5000 system Vision 5000 videoconferencing system Codec Vision 5000 Videoconferencing System CameraMonitors Vision 5000 Videoconferencing System Cart Remote control Tandberg AudioScience module optional Vision 5000 Videoconferencing System Table microphoneTandberg Natural Audio module optional on some systems This product complies with directives 89/366/EEC 93/261/EEC InstallationPrecautions Vision 5000 Videoconferencing System Installation Unpacking Installation Vision 5000 Videoconferencing SystemCamera Table Microphone Remote Control Batteries Connecting to the Switched 56 network Connecting cablesIsdn cables using BRI interface Isdn cable using the PRI/T1 interface Press OK to exit menu Power on monitorExample 29 monitor not USA Example 33 monitor not USA Press p+s/tp- to select Special FUNCTIONS, then press OK Power on codecTo highlight Switch on with, select AV with + keys Example monitor USA External Network configuration ConfigurationISDN-BRI configuration ISDN-PRI/T1 configuration Background Environmental considerationsIris control and lighting Do not place the camera facing a doorway Loudspeaker volumeBrightness control Seating Area Table Lighting Vision Vision 5000 Videoconferencing System Getting started Getting startedSystem start-up On-screen help To confirm the selection press OK BasicsGetting started Vision 5000 Videoconferencing System Video call Making and ending callsMaking a call Prefix Call Type Restricted callTelephone call SoftMux only Special call prefixes To answer a call, press Last number redial/using the call directoryIs switched off. See ‘Utilities’ Correcting keying mistakes General use Vision 5000 Videoconferencing System Adjusting volumeGeneral use View outgoing video Controlling the Main Camera Microphone on/offMoving the picture-in-picture PIP To manually focus the Main Camera, use the Focus keys Camera Tracking Highlighter bar to a source and press OK Enable/Disable Camera TrackingSelecting video sources Selecting audio sources Storing presets PresetsSelecting presets Requesting a still image Sending/receiving graphicsSending a still image Source and 0 to view the still image Receiving a still image Far end camera control Fecc Overview Advanced useGeneral Advanced use Vision 5000 Videoconferencing System All submenus are explained below Main menuMenu structure Video Call qualityAudio Motion Video ModeAudio Quality Status Format ResolutionLow resolution video 176 x 144 pixels Channels Alphabetic Sort Edit directory Both numbers should be specified 2x64 or 2x56 calls Add New EntryKey to delete the last character Store Last Number Far end camera control UtilitiesAutoanswer Do not disturb System Name Presentation SettingsThis menu allows setup of still-image/graphics transfer MCU status line Test subsystem Power up and system infoView current settings You can test the different subsystems of the Vision Call status BRI Status BRI Status PRI Comments Call status PRI Cause codes Most common cause codes for Isdn are Request floor MCU services Release chair Terminal IDChair control Take chair Allows the chairman to terminate the conference altogether Allows the chairman to release the floor Audio Inputs Audio setup Mic1 +3.0dB Mix ModeLevel Settings Inputs If an output is ‘Off’, no audio will be sent to that output Level Settings Outputs Echo Control Noise Reduction Tips for improving the echo canceller performance Alert Speaker Alert Tones & VolumeRestore Audio Defaults Enter a video source name Camera Track ModeVideo input Backlight Camera adjustmentsKeys on the remote control Focus Whitebalance Vision 5000 Videoconferencing System Advanced use Brightness Video output ISDN-BRI ISDN-PRI/T1 External Terminal settingsNetwork configuration Etsi Euro Isdn Isdn switch typeNtsc version is shown below Number2 Number Line Setup Subaddress Advanced Isdn settings Downspeed Default Call TypeMSN Multi Subscriber Number Parallel dial Cable Length 1&2 NumberMax Channels Channel Hunting Type Manufacturer PRI Switch Type settingPRI Switch Type AT&T Isdn National Isdn Call control RS366 Dialling Leased Line Data Triggered ManualRS449/V35 Compatible #006 6B call Bonding #002 #008 8B call Bonding #003 None Dataport configurationDataport 9600 Dataport 1 supports 4 different modes Control Modem 120 Data modeControl mode Modem mode Restore defaults IP-subnet mask TCP/IP SettingsIP-assignment IP-address Ethernet Vision 5000 Videoconferencing System What is neededEthernet Functionality WWW-interface Vision 5000 Videoconferencing System Ethernet How is it done Peripherals Vision 5000 Videoconferencing System Peripheral Equipment Video Outputs InterfacesVision 5000 Videoconferencing System Peripherals Video Inputs Dual Monitor optional Please contact your dealer for further information Natural Audio module optionalAudioScience module optional Tracker optional Multiple controllable cameras optional Document camera VCR Recording Video Cassette Recorder VCRVCR Playback Extra cameras Telephone Add-On VGA PAL/NTSC converter PC applicationsVGA to PAL converter Other PC applications Additional microphones Appendix Vision 5000 Videoconferencing System Appendices Vision 5000 Videoconferencing System Appendix Using Telesync TS-256 SW56/ISDN adapter Vision Configuration of Vision INC DSU Making a call Appendix 3 Connecting Vision 5000 to PRI/T1Using CSU adapter Configuration ofAdtran T1 ESF Csuace Appendix 4 LED indication Power Index Vision 5000 Videoconferencing System SymbolsIndex Imux Vision 5000 Videoconferencing System Index Index Vision 5000 Videoconferencing System

Far end camera control (FECC)

P2 P3 P4 or the keys 0-9 to activate presets P0-