MCU status line, System Name, Presentation Settings | TANDBERG 5000

VISION 5000 Videoconferencing System

Advanced use

Automatic call-up

When the automatic call-up function is On, the connection of the RTS line to the CTS line on Data Port 2 will initiate an out-going call to the number stored in entry 01 in the Directory (reserved for special applications).

MCU status line

During an MCU conference, a status line is displayed by default which provides user information about the conference. To remove this status line, select ‘MCU Status Line: Off’.

System Name

Identifies the system during an MCU conference call, when using the Web-interface and when the codec is acting as an SNMP Agent.

Presentation Settings

This menu allows setup of still-image/graphics transfer.

====== Presentation Settings ======

Presentation Mode: Normal Preview Still image source:

Current Video1 Video2

Video3 Video4 Video5 Previous Menu

Presentation Mode: Normal

GRAPHICS

To send a still-image immediately after pressing FREEZE , select ‘Presentation Mode: Normal’.

Presentation Mode: Preview

To preview your image before it is transferred as a still-image, select ‘Presentation Mode: Preview’. When

GRAPHICS

pressing FREEZE you will be allowed to view your image, e.g. from the document camera, before sending it as a

GRAPHICS

still-image by pressing FREEZE again.

Still image source

To select a default still image source, e.g. the document camera connected at video input 3, select ‘Still

GRAPHICS

image source: Video3’. When pressing FREEZE the system will switch to the chosen video input and send a still image from this video input. After the image is sent the system will switch back to the original video input.

To send a still image from your current video source, select ‘Still image source: Current’.

45

Image 45

TANDBERG 5000 MCU status line, System Name, Presentation Settings, This menu allows setup of still-image/graphics transfer

Contents

N D B E R G Vision 5000 Videoconferencing System Lysaker, Norway, Tel +47 67 125 125, Fax +47 67 125 Environmental Issues Vision 5000 Videoconferencing System Operator Safety Summary Contents Ethernet Functionality Vision 5000 Videoconferencing System Advanced usePeripheral Equipment Appendices Index Introduction How to use this guide Vision 5000 on-screen menu structure is shown below Menu structureRight keys to move through the menu structure Main menu At a glance the Vision 5000 system Vision 5000 videoconferencing system Vision 5000 Videoconferencing System Camera MonitorsCodec Vision 5000 Videoconferencing System Cart Remote control Vision 5000 Videoconferencing System Table microphone Tandberg Natural Audio module optional on some systemsTandberg AudioScience module optional Precautions InstallationVision 5000 Videoconferencing System Installation This product complies with directives 89/366/EEC 93/261/EEC Installation Vision 5000 Videoconferencing System Camera Table Microphone Remote Control BatteriesUnpacking Isdn cables using BRI interface Connecting cablesIsdn cable using the PRI/T1 interface Connecting to the Switched 56 network Example 29 monitor not USA Power on monitorExample 33 monitor not USA Press OK to exit menu To highlight Switch on with, select AV with + keys Power on codecExample monitor USA Press p+s/tp- to select Special FUNCTIONS, then press OK ISDN-BRI configuration ConfigurationISDN-PRI/T1 configuration External Network configuration Environmental considerations Iris control and lightingBackground Loudspeaker volume Brightness controlDo not place the camera facing a doorway Seating Area Table Lighting Vision System start-up Getting startedOn-screen help Vision 5000 Videoconferencing System Getting started Basics Getting started Vision 5000 Videoconferencing SystemTo confirm the selection press OK Making and ending calls Making a callVideo call Telephone call SoftMux only Restricted callSpecial call prefixes Prefix Call Type Is switched off. See ‘Utilities’ Last number redial/using the call directoryCorrecting keying mistakes To answer a call, press General use Adjusting volumeView outgoing video General use Vision 5000 Videoconferencing System Microphone on/off Moving the picture-in-picture PIPControlling the Main Camera To manually focus the Main Camera, use the Focus keys Camera Tracking Selecting video sources Enable/Disable Camera TrackingSelecting audio sources Highlighter bar to a source and press OK Presets Selecting presetsStoring presets Sending/receiving graphics Sending a still imageRequesting a still image Source and 0 to view the still image Receiving a still image Far end camera control Fecc General Advanced useAdvanced use Vision 5000 Videoconferencing System Overview Main menu Menu structureAll submenus are explained below Call quality AudioVideo Audio Video ModeQuality Motion Low resolution video 176 x 144 pixels ResolutionChannels Status Format Alphabetic Sort Edit directory Add New Entry Key to delete the last characterBoth numbers should be specified 2x64 or 2x56 calls Store Last Number Autoanswer UtilitiesDo not disturb Far end camera control This menu allows setup of still-image/graphics transfer Presentation SettingsMCU status line System Name View current settings Power up and system infoYou can test the different subsystems of the Vision Test subsystem Call status BRI Status BRI Status PRI Comments Call status PRI Cause codes Most common cause codes for Isdn are Request floor MCU services Chair control Terminal IDTake chair Release chair Allows the chairman to terminate the conference altogether Allows the chairman to release the floor Audio Inputs Audio setup Mix Mode Level Settings InputsMic1 +3.0dB If an output is ‘Off’, no audio will be sent to that output Level Settings Outputs Echo Control Noise Reduction Tips for improving the echo canceller performance Alert Tones & Volume Restore Audio DefaultsAlert Speaker Camera Track Mode Video inputEnter a video source name Keys on the remote control Camera adjustmentsFocus Backlight Whitebalance Vision 5000 Videoconferencing System Advanced use Brightness Video output Terminal settings Network configurationISDN-BRI ISDN-PRI/T1 External Isdn switch type Ntsc version is shown belowEtsi Euro Isdn Number2 Number Line Setup Subaddress Advanced Isdn settings MSN Multi Subscriber Number Default Call TypeParallel dial Downspeed Number Max ChannelsCable Length 1&2 PRI Switch Type Type Manufacturer PRI Switch Type settingAT&T Isdn National Isdn Channel Hunting RS366 Dialling Leased Line Data Triggered Manual RS449/V35 CompatibleCall control #006 6B call Bonding #002 #008 8B call Bonding #003 Dataport Dataport configuration9600 None Control mode Data modeModem mode Dataport 1 supports 4 different modes Control Modem 120 Restore defaults IP-assignment TCP/IP SettingsIP-address IP-subnet mask Ethernet Functionality What is neededWWW-interface Ethernet Vision 5000 Videoconferencing System Vision 5000 Videoconferencing System Ethernet How is it done Peripherals Vision 5000 Videoconferencing System Peripheral Equipment Vision 5000 Videoconferencing System Peripherals InterfacesVideo Inputs Video Outputs Dual Monitor optional Natural Audio module optional AudioScience module optionalPlease contact your dealer for further information Tracker optional Multiple controllable cameras optional Document camera Video Cassette Recorder VCR VCR PlaybackVCR Recording Extra cameras Telephone Add-On VGA to PAL converter PC applicationsOther PC applications VGA PAL/NTSC converter Additional microphones Appendix Vision 5000 Videoconferencing System Appendices Vision 5000 Videoconferencing System Appendix Using Telesync TS-256 SW56/ISDN adapter Vision Configuration of Vision INC DSU Using CSU adapter Appendix 3 Connecting Vision 5000 to PRI/T1Configuration ofAdtran T1 ESF Csuace Making a call Appendix 4 LED indication Power Symbols IndexIndex Vision 5000 Videoconferencing System Imux Vision 5000 Videoconferencing System Index Index Vision 5000 Videoconferencing System