Connections, System Examples | TOA Electronics C-RM500 instruction

7. CONNECTIONS

Note

To eliminate noise, be sure to connect the shield of a shielded twisted-pair cable to be used for connection between control terminals (for control) to the [GND] terminal.

Equipment Which Can Be Controlled with the C-RM500

Shown below are equipment that can be controlled with the C-RM500.

Camera: C-CC501, C-CC504, C-CC551, and C-CC554

Up to 31 cameras can be connected to the unit's Camera control terminal and controlled. The use of the C-IF500 Interface Unit will increase the number to up to 64 cameras (when the C-SS8 switcher is in use). Note that the cameras cannot be controlled if their number is greater than the number of inputs of a connected switcher.

Switcher: C-MS90D, C-MS90S, C-MS160D, C-MS160S, and C-SS8

Only one switcher can be connected for remote camera control. However, as to the C-SS8, 1 master-designated unit and up to 7 slave-designated units can be connected to remotely control the cameras.

About the Camera Control Terminal

The Camera control terminal is used to connect the C-CC501, C-CC504, C-CC551, or C-CC554 Combination Camera or the C-IF500 Interface Unit. Up to 31 pieces of equipment can be connected to the terminal.

7.1. System Examples

[Example 1]

Combination camera

C-RM500

Monitor TV

41

Image 41

TOA Electronics C-RM500 operating instructions Connections, System Examples

Contents

Operating Instructions Remote Controller Table of Contents Settings Safety Precautions Functions General DescriptionEquipment Which Can Be Controlled with the C-RM500 About the Camera Control Terminal Top Nomenclature and Functions Defroster key/Indicator *3 Lens speed key / Indicator *3Auxiliary contact key / Indicator *3 Auto key / Indicator *3 Rear Operating the Camera Operation P E R N U a LF R O S T E R X I L I a R Y S W Activating the automatic functions T OActivating the zoom function Activating the focus function O S I T I O N T O F O C U SChanging the lens speed Activating the auto-focus function Monitor Display When confirming the camera number and operating its displayA N N E L C a L L Operation keys Resetting individual freeze displays Simultaneously resetting all freeze displays Using the abbreviated numbers Using the Function keysU N C T I O N K E Y E T Viewing full-screen displays H a N N E LE G M E N T Monitor screen Group E G M E N T E G S E Q Q U E N C EViewing sequential displays Sequential full-screen viewing Sequential 4-segment split-screen viewing Alarm H O L D Alarm Hold and Reset Setting Items and Their Descriptions Settings LCD screen display Keys to be used in setting operationsOperating Keys and Display Screen S S W O R D Basic Setting OperationsE R a T I O N M O D E T O R E T U R N Operation mode Setting the FunctionsSetting contents E R a T I O N M O D E 1 . M a S T E R I T C H E R Switchers6 I N P U T M a R T Contact N T a C TE L E C T C H T O R E T U R N 1 . O N Automatic resetT O T U R N E C R a C E 2 P O S Home position selector terminal operation settingsR a C E Home position M E R a S P E E D4 0 M O T E Buzzer I T I a L S C R E E N 1 . F U L LZ Z E R 1 . O N Initial screen Channel designation I T I a L C H a N N E L M E R a Alarm 1 . O N N S O R Alarm 1 . O NSensor alarm Camera alarm Camera check Camera alarm preset Alarm time Alarm S I G N a L 1 . E D G EAlarm signal Alarm hold Alarm F U N C T I O N 1 . S E QAlarm H O L D 1 . K E Y M 1 N C T I O N K E YM 1 5 P O S 1 2 N C T I O N K E Y a a U T O P a N Abbreviation Setting the cameras alarm contact outputM 2 2 3 P 0 S E C 0 S E CTour sequence Press the Menu key to display the menu screen Camera menu PasswordM E R a M E N U C H Example ConnectionsSystem Examples Example Connection cables Connected Camera Termination Switch SettingConnection to Combination Cameras Connection to the Multi-Switchers RS-232C Terminal Fixed camera Connection to the Smart Switchers RS-232C Terminal Shielded twisted-pair cable RS-232C reverse cable RM500 Slave Speed Switcher Connection When Controlling the System from 2 Locations Alarm Output/Control Input Terminal Connections Assembling D-sub connectors onto cables Modifications SpecificationsAccessories 133-12-743-6E