Alarm S I G N a L 1 . E D G E, Alarm time | TOA Electronics C-RM500

6.4.14. Alarm signal

Sets continuous alarm operations.

Step 1. Press the Menu key to display the menu screen.

Step 2. Tilt the joystick up or down to select "ALARM SIGNAL," and confirm the selection with the SET key. The setting is displayed on Line 2.

A L A R M S I G N A L 1 . E D G E

Step 3. Tilt the joystick to the left or right to select either of the following settings, and confirm it with the SET key.

[Setting contents]

1.	EDGE	Terminates alarm operations when the time interval set in the "Alarm time" setting (next
		item) passes or when an alarm reset signal is received.

2.	LEVEL	Terminates alarm operations when the alarm input terminal receives alarm end data. Also,
		if "1. ON" has been selected in the "Camera alarm" setting, alarm operation will stop when
		all alarm signals from the camera change from make to break data.

Note: This selection is set to "1. EDGE" by the factory.

6.4.15. Alarm time

Sets the interval between alarm input and alarm reset.

Note

The Alarm Time can only be set when "1. EDGE" has been selected in the "Alarm signal" setting. This setting item is not displayed on the menu screen when "2. LEVEL" has been selected.

Step 1. Press the Menu key to display the menu screen.

Step 2. Tilt the joystick up or down to select "ALARM TIME," and confirm the selection with the SET key. The setting is displayed on Line 2.

A L A R M T I M E 3 . 2 0 S E C

Step 3. Tilt the joystick to the left or right to select one of the following settings, and confirm it with the SET key.

[Setting contents]

1.	10SEC	(10 seconds)	6.	2MIN	(2 minutes)
2.	15SEC	(15 seconds)	7.	3MIN	(3 minutes)

3.	20SEC	(20 seconds)	8.	4MIN	(4 minutes)

4.	30SEC	(30 seconds)	9.	5MIN	(5 minutes)
5.	1MIN	(1 minute)	10.	NO LIMIT	(no time limit)

Notes

•If "10. NO LIMIT" is selected, the alarm can only be reset when the Alarm Reset key on the unit's top panel is pressed.

•This selection is set to "3. 20SEC" by the factory.

35

Image 35

TOA Electronics C-RM500 operating instructions Alarm S I G N a L 1 . E D G E, Alarm signal, Alarm time

Contents

Operating Instructions Remote Controller Table of Contents Settings Safety Precautions About the Camera Control Terminal General DescriptionFunctions Equipment Which Can Be Controlled with the C-RM500 Top Nomenclature and Functions Auto key / Indicator *3 Lens speed key / Indicator *3Defroster key/Indicator *3 Auxiliary contact key / Indicator *3 Rear Operating the Camera Operation X I L I a R Y S W N U a LP E R F R O S T E R Activating the focus function T OActivating the automatic functions Activating the zoom function Activating the auto-focus function T O F O C U SO S I T I O N Changing the lens speed Operation keys When confirming the camera number and operating its displayMonitor Display A N N E L C a L L Resetting individual freeze displays Simultaneously resetting all freeze displays E T Using the Function keysUsing the abbreviated numbers U N C T I O N K E Y Viewing full-screen displays H a N N E LE G M E N T Monitor screen Group E G M E N T Sequential 4-segment split-screen viewing Q U E N C EE G S E Q Viewing sequential displays Sequential full-screen viewing Alarm H O L D Alarm Hold and Reset Setting Items and Their Descriptions Settings LCD screen display Keys to be used in setting operationsOperating Keys and Display Screen T O R E T U R N Basic Setting OperationsS S W O R D E R a T I O N M O D E E R a T I O N M O D E 1 . M a S T E R Setting the FunctionsOperation mode Setting contents M a R T SwitchersI T C H E R 6 I N P U T Contact N T a C TE L E C T C H E C Automatic resetT O R E T U R N 1 . O N T O T U R N Home position Home position selector terminal operation settingsR a C E 2 P O S R a C E M O T E S P E E DM E R a 4 0 Initial screen I T I a L S C R E E N 1 . F U L LBuzzer Z Z E R 1 . O N Channel designation I T I a L C H a N N E L Camera alarm N S O R Alarm 1 . O NM E R a Alarm 1 . O N Sensor alarm Camera check Camera alarm preset Alarm time Alarm S I G N a L 1 . E D G EAlarm signal Alarm hold Alarm F U N C T I O N 1 . S E QAlarm H O L D 1 . K E Y N C T I O N K E Y a a U T O P a N N C T I O N K E YM 1 M 1 5 P O S 1 2 Abbreviation Setting the cameras alarm contact outputM 2 Press the Menu key to display the menu screen 0 S E C2 3 P 0 S E C Tour sequence Camera menu PasswordM E R a M E N U C H Example ConnectionsSystem Examples Example Connection cables Connected Camera Termination Switch SettingConnection to Combination Cameras Connection to the Multi-Switchers RS-232C Terminal Fixed camera Connection to the Smart Switchers RS-232C Terminal Shielded twisted-pair cable RS-232C reverse cable RM500 Slave Speed Switcher Connection When Controlling the System from 2 Locations Alarm Output/Control Input Terminal Connections Assembling D-sub connectors onto cables Modifications SpecificationsAccessories 133-12-743-6E