I T I a L S C R E E N 1 . F U L L, Buzzer | TOA Electronics C-RM500

6.4.7. Buzzer

Sets whether or not to sound the buzzer when an alarm signal is received.

Step 1. Press the Menu key to display the menu screen.

Step 2. Tilt the joystick up or down to select "BUZZER," then confirm the selection with the SET key. The setting is displayed on Line 2.

B U Z Z E R 1 . O N

Step 3. Tilt the joystick left or right to select either of the following settings, and confirm it with the SET key.

[Setting contents]

1.	ON	Sounds a buzzer when alarm is activated.

2.	OFF	Sounds no buzzer when alarm is activated.

Note: This selection is set to "1. ON" by the factory.

6.4.8. Initial screen

Sets the screen to be displayed immediately after the power is turned on.

Step 1. Press the Menu key to display the menu screen.

Step 2. Tilt the joystick up or down to select "INITIAL SCREEN," then confirm the selection with the SET key. The setting will appear on Line 2.

I N I T I A L S C R E E N 1 . F U L L

Step 3. Tilt the joystick left or right to select one of the following settings, and confirm it with the SET key. Note: The settings differ depending on the type of switcher connected to the system.

[Setting contents]

Switcher Type		Setting

Multi-Switcher	1. FULL (full screen)
	2. SEQUENCE
	3.	4-SEG SEQ (sequential 4-segment split-screen display)
	4.	4-SEG (4-segment split-screen display)
	5.	9-SEG
	6.	10-SEG
	7.	16-SEG
	Notes
	• Make sure that the selected setting is the same as that for the connected switcher.
	• This selection is set to "3. 4-SEGMENT SEQ" by the factory.

Smart Switcher	1. FULL
	2. SEQUENCE
	Note: This selection is set to "SEQUENCE" by the factory.

Other switchers	1. FULL

30

Image 30

TOA Electronics C-RM500 operating instructions I T I a L S C R E E N 1 . F U L L, Buzzer, Z Z E R 1 . O N, Initial screen

Contents

Remote Controller Operating Instructions Table of Contents Settings Safety Precautions Equipment Which Can Be Controlled with the C-RM500 General DescriptionFunctions About the Camera Control Terminal Nomenclature and Functions Top Auxiliary contact key / Indicator *3 Lens speed key / Indicator *3Defroster key/Indicator *3 Auto key / Indicator *3 Rear Operation Operating the Camera F R O S T E R N U a LP E R X I L I a R Y S W Activating the zoom function T OActivating the automatic functions Activating the focus function Changing the lens speed T O F O C U SO S I T I O N Activating the auto-focus function A N N E L C a L L When confirming the camera number and operating its displayMonitor Display Operation keys Simultaneously resetting all freeze displays Resetting individual freeze displays U N C T I O N K E Y Using the Function keysUsing the abbreviated numbers E T H a N N E L E G M E N TViewing full-screen displays Monitor screen Group E G M E N T Viewing sequential displays Sequential full-screen viewing Q U E N C EE G S E Q Sequential 4-segment split-screen viewing Alarm Hold and Reset Alarm H O L D Settings Setting Items and Their Descriptions Keys to be used in setting operations Operating Keys and Display ScreenLCD screen display E R a T I O N M O D E Basic Setting OperationsS S W O R D T O R E T U R N Setting contents Setting the FunctionsOperation mode E R a T I O N M O D E 1 . M a S T E R 6 I N P U T SwitchersI T C H E R M a R T N T a C T E L E C T C HContact T O T U R N Automatic resetT O R E T U R N 1 . O N E C R a C E Home position selector terminal operation settingsR a C E 2 P O S Home position 4 0 S P E E DM E R a M O T E Z Z E R 1 . O N I T I a L S C R E E N 1 . F U L LBuzzer Initial screen I T I a L C H a N N E L Channel designation Sensor alarm N S O R Alarm 1 . O NM E R a Alarm 1 . O N Camera alarm Camera check Camera alarm preset Alarm S I G N a L 1 . E D G E Alarm signalAlarm time Alarm F U N C T I O N 1 . S E Q Alarm H O L D 1 . K E YAlarm hold M 1 5 P O S 1 2 N C T I O N K E YM 1 N C T I O N K E Y a a U T O P a N Setting the cameras alarm contact output M 2Abbreviation Tour sequence 0 S E C2 3 P 0 S E C Press the Menu key to display the menu screen Password M E R a M E N U C HCamera menu Connections System ExamplesExample Example Connected Camera Termination Switch Setting Connection to Combination CamerasConnection cables Connection to the Multi-Switchers RS-232C Terminal Fixed camera Connection to the Smart Switchers RS-232C Terminal Shielded twisted-pair cable RS-232C reverse cable Connection When Controlling the System from 2 Locations RM500 Slave Speed Switcher Alarm Output/Control Input Terminal Connections Assembling D-sub connectors onto cables Specifications AccessoriesModifications 133-12-743-6E