2 TROUBLESHOOTING FOR COPYING
Copying Problems
See the table below when you have a problem in operating copy function or have an unexpected copy output.
Problem Description | Cause | Corrective Action | ||
|
|
|
|
|
Functions cannot be set. | Another function that is unavailable | Some functions cannot be combined. | ||
|
|
| for the combination has already been | For details, refer to Chapter 8 of the Copying Guide. |
|
|
| set. |
|
|
|
|
|
|
Copying stops while scanning the | The number of scanned pages has | To copy the scanned images, press [YES]. To cancel, | ||
originals. (The message “The | reached the maximum. | press [NO]. | ||
number of originals exceeds the |
|
| ||
limits Will you print out stored |
|
| ||
originals?” appears.) |
|
| ||
|
|
|
|
|
Copying stops while scanning the | No available internal memory | To copy the scanned images, press [YES]. To cancel, | ||
originals. (The message “Not | remains. | press [NO]. | ||
enough Work Space to store |
|
| ||
originals Will you print out stored |
|
| ||
originals?” appears.) |
|
| ||
|
|
|
|
|
Copied image is too light. | No toner is left. | The message “Open the toner cover Install new toner | ||
|
|
|
| cartridge” appears when no toner is left. Replace the toner |
|
|
|
| cartridge. |
|
|
|
| P.37 “Replacing a Toner Cartridge” |
|
|
|
|
|
|
|
| Copy density is set too light. | Darken the density manually or try the automatic density |
|
|
|
| mode. |
|
|
|
|
|
Copied image is too dark. | Copy density is set too dark. | Lighten the density manually or try the automatic density | ||
|
|
|
| mode. |
|
|
|
|
|
Copied image has stains. | The Reversing Automatic Document | Lower them fully to block the outside light. | ||
|
|
| Feeder is not fully lowered. |
|
|
|
|
|
|
|
|
| The original glass, platen sheet, | Clean them. |
|
|
| scanning area and guide are stained. | P.98 “Regular Maintenance” |
|
|
|
|
|
|
|
| The copy density is set too dark. | Lighten the density manually or try the automatic density |
|
|
|
| mode. |
|
|
|
|
|
|
|
| A transparent original such as a | To copy a transparent original clearly, put a sheet of blank, |
|
|
| transparency or tracing paper is being | white paper behind the original. Make sure that the paper |
|
|
| used. | is large enough to cover the original. |
|
|
|
|
|
Copy image is skewed. | The original is sent from the | Replace the original while aligning the side guides of the | ||
|
|
| Reversing Automatic Document | Reversing Automatic Document Feeder to its width so that |
|
|
| Feeder at a skew. | it will be placed straight. |
|
|
|
|
|
Copied image is partially missing. | The size or orientation of the copy | Fit the copy paper size to the original or set the reduction | ||
|
|
| paper and that of the original are not | ratio for the copy paper. |
|
|
| consistent. The reduction ratio is not |
|
|
|
| properly set. |
|
|
|
|
|
|
|
|
| The binding margin is too wide. | Set the binding margin width to fully cover the original. |
|
|
|
| For details, refer to Chapter 4 of the Copying Guide. |
|
|
|
|
|
|
|
| The original is larger than the | The outside part of the printable area cannot be copied. |
|
|
| printable area. |
|
|
|
|
|
|
Copied image is blurred. | There is a gap between the original | Lower the Reversing Automatic Document Feeder fully so | ||
|
|
| glass and the original. | that the original fully contacts the platen glass. |
|
|
| The copy paper is damp. | Replace it with dry copy paper. |
|
|
|
|
|
|
|
|
|
|
