Stop | Toshiba G8000 instruction

14.5Stop

The procedure to stop the UPS is shown in Steps 1-3.

LED Key

- LED Off

- LED On

- LED Flash

BYPASS

AC - Vo 208 V

AC - Io 50%

PRESS ‘UPS’ SWITCH

STEP 1

Transfer to Bypass supply as described in Switch Power Supply.

AC INPUT

BATTERIES

BYPASS INPUT

CONVERTER

FLOAT CHARGE

EQUAL CHARGE

DISCHARGE

UPS

INVERTER

AC
SWITCH	AC OUTPUT
	AC OUTPUT
BYPASS

UPS LED is “OFF”. BYPASS LED is “ON”.

BYPASS

MOVE 72B TO ‘OFF’ POSITION

STEP 2

Turn off the DC Input Breaker (72B) on the external battery cabinet, and, press the G8000 “STOP” button for at least 0.5 seconds.

AC INPUT

BATTERIES

BYPASS INPUT

CONVERTER

FLOAT CHARGE

EQUAL CHARGE

DISCHARGE

INVERTER

UPS

AC
SWITCH	AC OUTPUT
	AC OUTPUT
BYPASS

BATTERIES LED is “OFF”.

INVERTER LED flashes then “OFF”.

FLOAT CHARGE LED and CONVERTER LED are “OFF”.

AC INPUT

BATTERIES

BYPASS INPUT

BYPASS

PRESS ‘RUN’ SWITCH

	UPS
CONVERTER	INVERTER
FLOAT CHARGE	AC
EQUAL CHARGE	AC
DISCHARGE	SWITCH

BYPASS

STEP 3

Wait until procedure is completed.

AC OUTPUT

G8000 Series with Isolated Output Installation and Operation Manual

53

Image 61

Toshiba G8000 operation manual Stop

Contents

G8000 Series Page G8000 Series Qualified Personnel only Uninterruptible Power System UPS Toshiba’s Customer Support Center PurposeToshiba Customer Support Center Toshiba International Corporation Table of Contents Terminal Blocks, Terminal Bus, and Power Cables 11.3 Introduction Symbols General Safety InstructionsProhibited Symbol indicates do not take action Qualified Personnel Signal Words Factory Authorized Personnel Important Safety Instructions Disclaimer Safety Precautions Keep the area arround the UPS clean General MaintenanceTransporting/Unpacking Do not tilt the UPS more than 10 from upright position Avoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its side Inspection/Storage Install the UPS in a controlled environment Installation PrecautionsKeep the Specified Clearance around the UPS Do not block air vents Do not install the UPS where water may fall on it Environment standard Installation PrecautionsPage Perform wiring and connections with correct polarity Wiring/ConnectionConnect only one 1 ground wire to the earth ground terminal Follow the torque criteria for tightening screws For 100 and 150 kVA GND 150kVA UPS Warning Labels Model Unit Shipping Weight and Dimensions 150kVA UPS Exterior Dimensions Inches Do not expose the unit to vibration or shock exceeding 0.5G Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By Crane Transporting UPS by Forklift Transporting By Forklift Storage/Operating Environment Operating PrecautionsPage Qualified Personnel only Maintenance PrecautionsQualified Personnel shall Do not dispose of the batteries in a fire DisposalDo not open or mutilate the batteries Installation UPS Clearance Unpacking Anchor Bolts Breaker UPS Wiring AC Input Bypass Input AC Output Battery Terminal Blocks, Terminal Bus, and Power Cables Block Number Cable Size Tightening Torque 100 KVA 150 KVA Bottom Cable Knockout Plates 100 kVA External Breakers Be sure to ground the UPS as specified Grounding Wire Signal Name Operation Control Wires Connection Between UPS, Battery Cabinet & Bypass Breaker Jumper Cable Between the Neutral Terminal & Ground BUS Grounding Configuration General Specification UPS SpecificationsMechanical Specification Rated Capacity 150kVA Do not open the front cover Electrical Specification UPS may not respond if the button press is too short Operator Interface Graphic display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and Buttons Graphic display Panel LCD/LED INDICAtors 13.2 LCD/LED Indicators Name Description LCD Indicators AC-VO AC- I O 50% Normal DisplayVolt Freq .0Hz 50% BYP I/P-V Freq .0Hz AC I/P-V Freq .0HzDC-V BATT-V BATT- I 0A 32TIM 09-09-06 Fault Display Abbreveations LCD Scroll Operating the UPS Epo and Control Power supply operating switches Pre-operational Check Operation TypesPerform the pre-operational check before operating the UPS Step Startup Procedures AC Vo 208 AC Io 50% Bypass LED is on Switch Power Supply UPS→Bypass Stop DC-V 0 BATT-V 0 BATT-I 0 a Complete Shutdown Make sure that the Float Charge LED is on Changing Between Float Charge and Equalize Charge Make sure that the Batt FAULT1 warning goes away Emergency Power Off EPO TroubleshootingTypes of Errors 09-09-06 Faults and Warnings Data Screen Fault Display LCD Fault & Warning Displays Over Heat Fault Messages AC O/P UV Button functions LCD Scroll w/ faults or warnings Restoring UPS Operation Contact Toshiba in the event of malfunction or faultDo not attempt to modify or relocate the UPS Do not open the front and/or rear panelsPage Page Industrial Division