Complete Shutdown, DC-V 0 BATT-V 0 BATT-I 0 a | Toshiba G8000

14.6Complete Shutdown

The procedure to turn off the control power and shut down the UPS completely is shown in Steps 1-6.

STEP 1

Transfer to Bypass supply as described in Switch Power Supply.

UPS LED is “OFF”. BYPASS LED is “ON”.

BYPASS

DC-V 0 [V]

BATT-V 0 [V]

BATT-I 0 [A]

STEP 2

Turn off the DC Input Breaker on the external battery cabinet, and, press the “STOP” button for at least 0.5 sec.

BATTERIES LED is “OFF”.

INVERTER LED flashes then “OFF”.

FLOAT CHARGE LED and CONVERTER LED are “OFF”.

STEP 3

Wait until procedure is completed.

STEP 4

Scroll the LCD screen to see the DC INPUT and make sure DC bus voltage is 0V.

STEP 5

*Turn off the control power supply switch (8A). Nothing is displayed on the LCD.

All LED’s are “OFF”.

STEP 6

Turn off all breakers at AC output, Bypass Input and AC Output.

Shutdown is completed and UPS is isolated.

ATTENTION

*STEP 5 - This operation is different from the instructions displayed on the screen.

Be sure to perform the procedure as specified in this manual.

54	G8000 Series with Isolated Output Installation and Operation Manual

Image 62

Toshiba G8000 operation manual Complete Shutdown, DC-V 0 BATT-V 0 BATT-I 0 a

Contents

G8000 Series Page G8000 Series Qualified Personnel only Uninterruptible Power System UPS Toshiba Customer Support Center PurposeToshiba’s Customer Support Center Toshiba International Corporation Table of Contents Terminal Blocks, Terminal Bus, and Power Cables 11.3 Introduction Prohibited Symbol indicates do not take action General Safety InstructionsSymbols Signal Words Qualified Personnel Important Safety Instructions Factory Authorized Personnel Safety Precautions Disclaimer Transporting/Unpacking General MaintenanceKeep the area arround the UPS clean Do not tilt the UPS more than 10 from upright position Do not transport, move, store, or place the UPS on its side Avoid vibration or shock exceeding 0.5G Inspection/Storage Keep the Specified Clearance around the UPS Installation PrecautionsInstall the UPS in a controlled environment Do not install the UPS where water may fall on it Do not block air vents Installation Precautions Environment standardPage Connect only one 1 ground wire to the earth ground terminal Wiring/ConnectionPerform wiring and connections with correct polarity Follow the torque criteria for tightening screws For 100 and 150 kVA GND 150kVA UPS Warning Labels Weight and Dimensions Model Unit Shipping 150kVA UPS Exterior Dimensions Inches Transporting Do not expose the unit to vibration or shock exceeding 0.5G Transporting By Crane 8.5 show examples of acceptable and unacceptable operations Transporting By Forklift Transporting UPS by Forklift Operating Precautions Storage/Operating EnvironmentPage Qualified Personnel shall Maintenance PrecautionsQualified Personnel only Do not open or mutilate the batteries DisposalDo not dispose of the batteries in a fire Installation Unpacking UPS Clearance Anchor Bolts UPS Wiring Breaker Terminal Blocks, Terminal Bus, and Power Cables AC Input Bypass Input AC Output Battery Block Number Cable Size Tightening Torque 100 KVA 150 KVA External Breakers Bottom Cable Knockout Plates 100 kVA Grounding Wire Be sure to ground the UPS as specified Control Wires Signal Name Operation Connection Between UPS, Battery Cabinet & Bypass Breaker Grounding Configuration Jumper Cable Between the Neutral Terminal & Ground BUS Mechanical Specification UPS SpecificationsGeneral Specification Rated Capacity 150kVA Electrical Specification Do not open the front cover Operator Interface UPS may not respond if the button press is too short Key-Switch and Buttons Graphic display Panel KEY-SWITCH/OPERATING Buttons 13.2 LCD/LED Indicators Graphic display Panel LCD/LED INDICAtors LCD Indicators Name Description Volt Freq .0Hz Normal DisplayAC-VO AC- I O 50% 50% DC-V BATT-V BATT- I 0A AC I/P-V Freq .0HzBYP I/P-V Freq .0Hz 32TIM Fault Display 09-09-06 LCD Scroll Abbreveations Epo and Control Power supply operating switches Operating the UPS Perform the pre-operational check before operating the UPS Operation TypesPre-operational Check Startup Procedures Step AC Vo 208 AC Io 50% Switch Power Supply UPS→Bypass Bypass LED is on Stop Complete Shutdown DC-V 0 BATT-V 0 BATT-I 0 a Changing Between Float Charge and Equalize Charge Make sure that the Float Charge LED is on Make sure that the Batt FAULT1 warning goes away Types of Errors TroubleshootingEmergency Power Off EPO Faults and Warnings Data Screen 09-09-06 LCD Fault & Warning Displays Fault Display Fault Messages Over Heat AC O/P UV LCD Scroll w/ faults or warnings Button functions Do not attempt to modify or relocate the UPS Contact Toshiba in the event of malfunction or faultRestoring UPS Operation Do not open the front and/or rear panelsPage Page Industrial Division