Startup Procedures, Step | Toshiba G8000 specs

14.3Startup Procedures

The procedure to start the UPS is shown in Steps 1-5.

STEP 1

Turn on the control power supply switch. (Figure 14.1) and ensure the operation lock is set to OPERATION. (Figure 13.1 - 1)

LED Key

- LED Off

- LED On

- LED Flash

SYSTEM INITIALIZE

AC INPUT

BATTERIES

BYPASS INPUT

CONVERTER

FLOAT CHARGE

EQUAL CHARGE

DISCHARGE

UPS

INVERTER

AC
SWITCH	AC OUTPUT
	AC OUTPUT
BYPASS

STEP 2

Wait for a few seconds.

AC INPUT

BATTERIES

BYPASS INPUT

BYPASS

PRESS ‘RUN’ SWITCH

	UPS
CONVERTER	INVERTER
FLOAT CHARGE	AC
EQUAL CHARGE	AC
DISCHARGE	SWITCH	AC OUTPUT
DISCHARGE		AC OUTPUT

BYPASS

STEP 3

Press the “RUN” button for at least 0.5 seconds.

CONVERTER LED is “ON” and INVERTER LED flashes.

AC INPUT

BATTERIES

BYPASS INPUT

BYPASS

UPS STARTING

WAIT FOR A WHILE

	UPS
CONVERTER	INVERTER
FLOAT CHARGE	AC
EQUAL CHARGE	AC
DISCHARGE	SWITCH	AC OUTPUT
DISCHARGE		AC OUTPUT

BYPASS

50	G8000 Series with Isolated Output Installation and Operation Manual

Image 58

Toshiba G8000 operation manual Startup Procedures, Step

Contents

G8000 Series Page G8000 Series Qualified Personnel only Uninterruptible Power System UPS Toshiba Customer Support Center PurposeToshiba’s Customer Support Center Toshiba International Corporation Table of Contents Terminal Blocks, Terminal Bus, and Power Cables 11.3 Introduction Symbols General Safety InstructionsProhibited Symbol indicates do not take action Signal Words Qualified Personnel Important Safety Instructions Factory Authorized Personnel Safety Precautions Disclaimer Transporting/Unpacking General MaintenanceKeep the area arround the UPS clean Do not tilt the UPS more than 10 from upright position Do not transport, move, store, or place the UPS on its side Avoid vibration or shock exceeding 0.5G Inspection/Storage Install the UPS in a controlled environment Installation PrecautionsKeep the Specified Clearance around the UPS Do not install the UPS where water may fall on it Do not block air vents Installation Precautions Environment standardPage Connect only one 1 ground wire to the earth ground terminal Wiring/ConnectionPerform wiring and connections with correct polarity Follow the torque criteria for tightening screws For 100 and 150 kVA GND 150kVA UPS Warning Labels Weight and Dimensions Model Unit Shipping 150kVA UPS Exterior Dimensions Inches Transporting Do not expose the unit to vibration or shock exceeding 0.5G Transporting By Crane 8.5 show examples of acceptable and unacceptable operations Transporting By Forklift Transporting UPS by Forklift Operating Precautions Storage/Operating EnvironmentPage Qualified Personnel only Maintenance PrecautionsQualified Personnel shall Do not dispose of the batteries in a fire DisposalDo not open or mutilate the batteries Installation Unpacking UPS Clearance Anchor Bolts UPS Wiring Breaker Terminal Blocks, Terminal Bus, and Power Cables AC Input Bypass Input AC Output Battery Block Number Cable Size Tightening Torque 100 KVA 150 KVA External Breakers Bottom Cable Knockout Plates 100 kVA Grounding Wire Be sure to ground the UPS as specified Control Wires Signal Name Operation Connection Between UPS, Battery Cabinet & Bypass Breaker Grounding Configuration Jumper Cable Between the Neutral Terminal & Ground BUS General Specification UPS SpecificationsMechanical Specification Rated Capacity 150kVA Electrical Specification Do not open the front cover Operator Interface UPS may not respond if the button press is too short Key-Switch and Buttons Graphic display Panel KEY-SWITCH/OPERATING Buttons 13.2 LCD/LED Indicators Graphic display Panel LCD/LED INDICAtors LCD Indicators Name Description Volt Freq .0Hz Normal DisplayAC-VO AC- I O 50% 50% DC-V BATT-V BATT- I 0A AC I/P-V Freq .0HzBYP I/P-V Freq .0Hz 32TIM Fault Display 09-09-06 LCD Scroll Abbreveations Epo and Control Power supply operating switches Operating the UPS Pre-operational Check Operation TypesPerform the pre-operational check before operating the UPS Startup Procedures Step AC Vo 208 AC Io 50% Switch Power Supply UPS→Bypass Bypass LED is on Stop Complete Shutdown DC-V 0 BATT-V 0 BATT-I 0 a Changing Between Float Charge and Equalize Charge Make sure that the Float Charge LED is on Make sure that the Batt FAULT1 warning goes away Emergency Power Off EPO TroubleshootingTypes of Errors Faults and Warnings Data Screen 09-09-06 LCD Fault & Warning Displays Fault Display Fault Messages Over Heat AC O/P UV LCD Scroll w/ faults or warnings Button functions Do not attempt to modify or relocate the UPS Contact Toshiba in the event of malfunction or faultRestoring UPS Operation Do not open the front and/or rear panelsPage Page Industrial Division