LCD Scroll, Abbreveations | Toshiba G8000 manual

13.6LCD Scroll

Scroll through the LCD display screens (see Figure 10.4), in sequence, using the “SCROLL UP” and “SCROLL DOWN” buttons on the graphic display panel.

•SCROLL UP - Moves back to the previous screen

•SCROLL DOWN - Moves forward to the next screen

TABLE 13.4 display screen scroll sequence

UPS SUPPLY

AC-VO 208[V]

AC- I O 50[%]

OPERATION MODE

NORMAL OPERATION

MODE SYNC.

(The LCD displays a

diagram of the electrical

power flow.)

Abbreveations

AC – Alternating Current

DC	–	Direct Current
IO	–	Current
		Output
I/P	–	Input
O/P	–	Output
VO	–	Voltage
		Output

FAULTS & WARNINGS

NO FAULT

NO WARNING

CLOCK

TIME 03-24-06 13:58

MODE COUNT

UPS 35[H] BATTERY 56[MIN]

32[TIM]

O/P VOLTAGE

VOLT. 208[V]

FREQ. 60.0[Hz]

O/P CURRENT (R.M.S.)

U50[%]

V50[%] W 50[%]

O/P CURRENT (Peak)

U50[%]

V50[%] W 50[%]

AC INPUT

AC I/P-V 480[V]

FREQ. 60.0[Hz]

DC INPUT

DC-V 632[V]

BATT-V 400[V]

BATT- I 0[A]

BATTERY

BACK-UP RATING 10[MIN]

DISCHARGING 15[MIN]

Bypass INPUT

BYP I/P-V 480[V]

FREQ. 60.0[Hz]

G8000 Series with Isolated Output Installation and Operation Manual

47

Image 55

Toshiba G8000 operation manual LCD Scroll, Abbreveations

Contents

G8000 Series Page G8000 Series Qualified Personnel only Uninterruptible Power System UPS Toshiba International Corporation PurposeToshiba’s Customer Support Center Toshiba Customer Support Center Table of Contents Terminal Blocks, Terminal Bus, and Power Cables 11.3 Introduction Symbols General Safety InstructionsProhibited Symbol indicates do not take action Qualified Personnel Signal Words Factory Authorized Personnel Important Safety Instructions Disclaimer Safety Precautions Do not tilt the UPS more than 10 from upright position General MaintenanceKeep the area arround the UPS clean Transporting/Unpacking Avoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its side Inspection/Storage Install the UPS in a controlled environment Installation PrecautionsKeep the Specified Clearance around the UPS Do not block air vents Do not install the UPS where water may fall on it Environment standard Installation PrecautionsPage Follow the torque criteria for tightening screws Wiring/ConnectionPerform wiring and connections with correct polarity Connect only one 1 ground wire to the earth ground terminal For 100 and 150 kVA GND 150kVA UPS Warning Labels Model Unit Shipping Weight and Dimensions 150kVA UPS Exterior Dimensions Inches Do not expose the unit to vibration or shock exceeding 0.5G Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By Crane Transporting UPS by Forklift Transporting By Forklift Storage/Operating Environment Operating PrecautionsPage Qualified Personnel only Maintenance PrecautionsQualified Personnel shall Do not dispose of the batteries in a fire DisposalDo not open or mutilate the batteries Installation UPS Clearance Unpacking Anchor Bolts Breaker UPS Wiring AC Input Bypass Input AC Output Battery Terminal Blocks, Terminal Bus, and Power Cables Block Number Cable Size Tightening Torque 100 KVA 150 KVA Bottom Cable Knockout Plates 100 kVA External Breakers Be sure to ground the UPS as specified Grounding Wire Signal Name Operation Control Wires Connection Between UPS, Battery Cabinet & Bypass Breaker Jumper Cable Between the Neutral Terminal & Ground BUS Grounding Configuration General Specification UPS SpecificationsMechanical Specification Rated Capacity 150kVA Do not open the front cover Electrical Specification UPS may not respond if the button press is too short Operator Interface Graphic display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and Buttons Graphic display Panel LCD/LED INDICAtors 13.2 LCD/LED Indicators Name Description LCD Indicators 50% Normal DisplayAC-VO AC- I O 50% Volt Freq .0Hz 32TIM AC I/P-V Freq .0HzBYP I/P-V Freq .0Hz DC-V BATT-V BATT- I 0A 09-09-06 Fault Display Abbreveations LCD Scroll Operating the UPS Epo and Control Power supply operating switches Pre-operational Check Operation TypesPerform the pre-operational check before operating the UPS Step Startup Procedures AC Vo 208 AC Io 50% Bypass LED is on Switch Power Supply UPS→Bypass Stop DC-V 0 BATT-V 0 BATT-I 0 a Complete Shutdown Make sure that the Float Charge LED is on Changing Between Float Charge and Equalize Charge Make sure that the Batt FAULT1 warning goes away Emergency Power Off EPO TroubleshootingTypes of Errors 09-09-06 Faults and Warnings Data Screen Fault Display LCD Fault & Warning Displays Over Heat Fault Messages AC O/P UV Button functions LCD Scroll w/ faults or warnings Do not open the front and/or rear panels Contact Toshiba in the event of malfunction or faultRestoring UPS Operation Do not attempt to modify or relocate the UPSPage Page Industrial Division