G8000 Series | Toshiba specs

Uninterruptible Power System (UPS)

G8000 SERIES

with Isolated Output

INSTALLATION and OPERATION MANUAL

Document: 59942-001

November 2007

G8000 Series with Isolated Output Installation and Operation Manual

Image 3

Toshiba operation manual G8000 Series

Contents

G8000 Series Page G8000 Series Qualified Personnel only Uninterruptible Power System UPS Toshiba International Corporation PurposeToshiba’s Customer Support Center Toshiba Customer Support Center Table of Contents Terminal Blocks, Terminal Bus, and Power Cables 11.3 Introduction General Safety Instructions SymbolsProhibited Symbol indicates do not take action Qualified Personnel Signal Words Factory Authorized Personnel Important Safety Instructions Disclaimer Safety Precautions Do not tilt the UPS more than 10 from upright position General MaintenanceKeep the area arround the UPS clean Transporting/Unpacking Avoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its side Inspection/Storage Installation Precautions Install the UPS in a controlled environmentKeep the Specified Clearance around the UPS Do not block air vents Do not install the UPS where water may fall on it Environment standard Installation PrecautionsPage Follow the torque criteria for tightening screws Wiring/ConnectionPerform wiring and connections with correct polarity Connect only one 1 ground wire to the earth ground terminal For 100 and 150 kVA GND 150kVA UPS Warning Labels Model Unit Shipping Weight and Dimensions 150kVA UPS Exterior Dimensions Inches Do not expose the unit to vibration or shock exceeding 0.5G Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By Crane Transporting UPS by Forklift Transporting By Forklift Storage/Operating Environment Operating PrecautionsPage Maintenance Precautions Qualified Personnel onlyQualified Personnel shall Disposal Do not dispose of the batteries in a fireDo not open or mutilate the batteries Installation UPS Clearance Unpacking Anchor Bolts Breaker UPS Wiring AC Input Bypass Input AC Output Battery Terminal Blocks, Terminal Bus, and Power Cables Block Number Cable Size Tightening Torque 100 KVA 150 KVA Bottom Cable Knockout Plates 100 kVA External Breakers Be sure to ground the UPS as specified Grounding Wire Signal Name Operation Control Wires Connection Between UPS, Battery Cabinet & Bypass Breaker Jumper Cable Between the Neutral Terminal & Ground BUS Grounding Configuration UPS Specifications General SpecificationMechanical Specification Rated Capacity 150kVA Do not open the front cover Electrical Specification UPS may not respond if the button press is too short Operator Interface Graphic display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and Buttons Graphic display Panel LCD/LED INDICAtors 13.2 LCD/LED Indicators Name Description LCD Indicators 50% Normal DisplayAC-VO AC- I O 50% Volt Freq .0Hz 32TIM AC I/P-V Freq .0HzBYP I/P-V Freq .0Hz DC-V BATT-V BATT- I 0A 09-09-06 Fault Display Abbreveations LCD Scroll Operating the UPS Epo and Control Power supply operating switches Operation Types Pre-operational CheckPerform the pre-operational check before operating the UPS Step Startup Procedures AC Vo 208 AC Io 50% Bypass LED is on Switch Power Supply UPS→Bypass Stop DC-V 0 BATT-V 0 BATT-I 0 a Complete Shutdown Make sure that the Float Charge LED is on Changing Between Float Charge and Equalize Charge Make sure that the Batt FAULT1 warning goes away Troubleshooting Emergency Power Off EPOTypes of Errors 09-09-06 Faults and Warnings Data Screen Fault Display LCD Fault & Warning Displays Over Heat Fault Messages AC O/P UV Button functions LCD Scroll w/ faults or warnings Do not open the front and/or rear panels Contact Toshiba in the event of malfunction or faultRestoring UPS Operation Do not attempt to modify or relocate the UPSPage Page Industrial Division