AC I/P-V Freq .0Hz, BYP I/P-V Freq .0Hz, 32TIM | Toshiba G8000

MEASUREMENT SCREENS

O/P CURRENT (PEAK)

TABLE 13.2 - CONTINUED

Shows the peak output current peak (%) for each phase.

U50[%]

V50[%]

W50[%]

Peak value of output current

RMS value for rated current x 1.41

x 100 [%]

AC INPUT

AC I/P-V 480[V]

FREQ. 60.0[Hz]

BYPASS INPUT

BYP I/P-V 480[V]

FREQ. 60.0[Hz]

Shows the AC Input Voltage (line-to-line) and frequency.

Shows the Bypass Input Voltage (line-to-line voltage) and frequency. .

BATTERY

BACK-UP RATING 10[MIN]

DISCHARGING 15[MIN]

Shows the remaining battery backup time with rated load and cumulative discharged time.

DC INPUT

DC-V 632[V]

BATT-V 400[V]

BATT- I 0[A]

MODE COUNT

UPS 35[H] BATTERY 56[MIN]

32[TIM]

CLOCK

TIME 03-24-06 13:58

Shows the internal DC bus voltage, battery voltage and battery current.

The battery current value displayed is negative during recharge and positive during discharge.

Shows the cumulative UPS operation time, the cumulative battery backup time and the number of battery backup operations.

The current time is displayed if there are no faults recorded, or after the reset button is pressed.

Date is displayed in the mm-ddyyy format. The unit does not calculate daylight savings time.

Time is displayed in the 24-hour format (e.g. 1:58 P.M. = 1358 Hrs.)

G8000 Series with Isolated Output Installation and Operation Manual

45

Image 53

Toshiba G8000 operation manual AC I/P-V Freq .0Hz, BYP I/P-V Freq .0Hz, DC-V BATT-V BATT- I 0A, 32TIM, Time 03-24-06

Contents

G8000 Series Page G8000 Series Qualified Personnel only Uninterruptible Power System UPS Toshiba’s Customer Support Center PurposeToshiba Customer Support Center Toshiba International Corporation Table of Contents Terminal Blocks, Terminal Bus, and Power Cables 11.3 Introduction Prohibited Symbol indicates do not take action General Safety InstructionsSymbols Qualified Personnel Signal Words Factory Authorized Personnel Important Safety Instructions Disclaimer Safety Precautions Keep the area arround the UPS clean General MaintenanceTransporting/Unpacking Do not tilt the UPS more than 10 from upright position Avoid vibration or shock exceeding 0.5G Do not transport, move, store, or place the UPS on its side Inspection/Storage Keep the Specified Clearance around the UPS Installation PrecautionsInstall the UPS in a controlled environment Do not block air vents Do not install the UPS where water may fall on it Environment standard Installation PrecautionsPage Perform wiring and connections with correct polarity Wiring/ConnectionConnect only one 1 ground wire to the earth ground terminal Follow the torque criteria for tightening screws For 100 and 150 kVA GND 150kVA UPS Warning Labels Model Unit Shipping Weight and Dimensions 150kVA UPS Exterior Dimensions Inches Do not expose the unit to vibration or shock exceeding 0.5G Transporting 8.5 show examples of acceptable and unacceptable operations Transporting By Crane Transporting UPS by Forklift Transporting By Forklift Storage/Operating Environment Operating PrecautionsPage Qualified Personnel shall Maintenance PrecautionsQualified Personnel only Do not open or mutilate the batteries DisposalDo not dispose of the batteries in a fire Installation UPS Clearance Unpacking Anchor Bolts Breaker UPS Wiring AC Input Bypass Input AC Output Battery Terminal Blocks, Terminal Bus, and Power Cables Block Number Cable Size Tightening Torque 100 KVA 150 KVA Bottom Cable Knockout Plates 100 kVA External Breakers Be sure to ground the UPS as specified Grounding Wire Signal Name Operation Control Wires Connection Between UPS, Battery Cabinet & Bypass Breaker Jumper Cable Between the Neutral Terminal & Ground BUS Grounding Configuration Mechanical Specification UPS SpecificationsGeneral Specification Rated Capacity 150kVA Do not open the front cover Electrical Specification UPS may not respond if the button press is too short Operator Interface Graphic display Panel KEY-SWITCH/OPERATING Buttons Key-Switch and Buttons Graphic display Panel LCD/LED INDICAtors 13.2 LCD/LED Indicators Name Description LCD Indicators AC-VO AC- I O 50% Normal DisplayVolt Freq .0Hz 50% BYP I/P-V Freq .0Hz AC I/P-V Freq .0HzDC-V BATT-V BATT- I 0A 32TIM 09-09-06 Fault Display Abbreveations LCD Scroll Operating the UPS Epo and Control Power supply operating switches Perform the pre-operational check before operating the UPS Operation TypesPre-operational Check Step Startup Procedures AC Vo 208 AC Io 50% Bypass LED is on Switch Power Supply UPS→Bypass Stop DC-V 0 BATT-V 0 BATT-I 0 a Complete Shutdown Make sure that the Float Charge LED is on Changing Between Float Charge and Equalize Charge Make sure that the Batt FAULT1 warning goes away Types of Errors TroubleshootingEmergency Power Off EPO 09-09-06 Faults and Warnings Data Screen Fault Display LCD Fault & Warning Displays Over Heat Fault Messages AC O/P UV Button functions LCD Scroll w/ faults or warnings Restoring UPS Operation Contact Toshiba in the event of malfunction or faultDo not attempt to modify or relocate the UPS Do not open the front and/or rear panelsPage Page Industrial Division