5.Installation
5.1General Safety Instructions
•Read all of these instructions. Save them for future reference.
•Follow all warnings and instructions marked on the device.
•Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result.
•Do not use the device near water.
•Do not place the device near, or over, radiators or heat registers.
•The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered.
•The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided.
•Never spill liquid of any kind on the device.
•Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
•The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
•This device is designed for IT power distribution systems with up to 230V phase to phase voltage.
•The device is equipped with a
•Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over.
•If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
•Consideration should be given to the connection of equipment to the supply circuit, and what effect overloading the supply circuit might have on overcurrent protection and supply wiring.
•To help protect your system from sudden, transient increases and decreases in electrical power, use a Tripp Lite Surge Suppressor, Line Conditioner, or Uninterruptible Power Supply (UPS).
•Position system cables and power cables carefully; be sure that nothing rests on any cables.
•When connecting or disconnecting power to hot pluggable power supplies, observe the following guidelines:
• Install the power supply before connecting the power cable to the power supply.
• Unplug the power cable before removing the power supply.
• If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from the power supplies.
•Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock.
•Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.
•If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair:
•The power cord or plug has become damaged or frayed.
•Liquid has been spilled into the device.
•The device has been exposed to rain or water.
•The device has been dropped, or the cabinet has been damaged.
•The device exhibits a distinct change in performance, indicating a need for service.
•The device does not operate normally when the operating instructions are followed.
•Only adjust those controls that are covered in the operating instructions. Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.
•Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.
Rack Mounting
•The ambient operating temperature in the rack may be an issue and is dependent upon the rack load and ventilation. When installing in a closed or
•Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack.
•Always load the rack from the bottom up, and load the heaviest item in the rack first.
•Always load the rack so that a hazardous condition is not created due to uneven loading.
•Make sure that the rack is level and stable before extending a device from the rack.
•Use caution when pressing the device rail release latches and sliding a device into or out of a rack; the slide rails can pinch your fingers.
•After a device is inserted into the rack, carefully extend the rail into a locking position, and then slide the device into the rack.
•Do not overload the AC supply branch circuit that provides power to the rack. The total rack load should not exceed 80 percent of the branch circuit rating.
•Ensure that proper airflow is provided to devices in the rack.
•Do not step on or stand on any device when servicing other devices in a rack.
8
