Code 128 see, MSI / Plessey Code, Code 93 see | Unitech MS860

PROGRAMMING VIA SCANNER INPUT

Symbologies - Group 7

Enter Group 7

0

1

2

3

4

5

6

7

8

9

73

Group Default

Code 128: (see page 51)

0/1 - Disable / Enable

1 ~ 64 - Min. Length 1 /G1 Max. Length 64

(see page 72 for Min./Max. Length procedure)

	MSI / Plessey Code:
	(see page 52)
	0/1 - Disable / Enable	G2
	2/3 - Check Digit Send /	G2
	2/3 - Check Digit Send /

No Send

4 - Check Digit Double Module 10

5 - Check Digit Module 11 Plus 10

6 - Check Digit Single Module 10

1 ~ 16 - Min. Length 1 / Max. Length 16 (see page 72 for Min./Max. Length procedure)

Code 93: (see page 52)

0/1 - Disable / Enable

1 ~ 48 - Min. Length 1 /G3 Max. Length 48

(see page 72 for Min./Max. Length procedure)

Exit

MS860 WiFi Manual

Image 75

Unitech MS860 manual Code 128 see, MSI / Plessey Code, No Send Check Digit Double Module, Code 93 see

Contents

MS860 WiFi Bar Code Scanner Table of Contents Introduction Introduction Quick Start Important Notes Importantscanner Ndotesaccessories Scanner LED Scanner Parts Buzzer Cradle LEDs Cradle Parts Charging the Scanner How to determine if the scanner needs recharging Network Settings Modifying the WiFi settings IP Address Glossary WEP Using SCM for Scanner Network Setting Network Settings Network Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Keyboard Wedge Beeps and DelaysInterblock Delay Intercharacter Delay Use Numeric Keypad Function CodeCaps-Lock Language Handshaking Baud RateParity Data Bit Data Direction RS232BCC Character Time Out Terminator Scanner Port Double Verification Use Code ID Settings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Label Type Scanning Mode Postamble Aim Function for Long Range EngineAiming Time for Long Range Engine Preamble Code Bar Code Symbologies Interleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code UPC-A Codabar EAN-13 UPC-E Delta Code EAN-8 Label Code IV Supplement Code for UPC-E, ISBN, EAN-13 Data Editing QualifierModifier Scanner Configuration Manager Everything Else Formula Arrange Formulas Introduction Programming VIA Scanner Input Beep Quick Setup Bar Codes UPC-E Medium Interblock DelayIntercharacter Delay Beep Tone see page 40 0 None Keyboard Interface None Baud Rate9600 Parity Data Direction for terminal wedge see Send to Host Second Define Code ID TerminatorEnter Code ID Label Type Scanning ModeDouble Verification Trigger Ppoo Interleaved 2 of 5 ITF see Symbologies GroupCode 39 see Check Digit Not Calculate UCC/EAN 128 see Standard 2 China Postal Code Toshiba CodeCode 32 Italian Pharmacy see Telepen Define the EAN 128 Fields Separator Define a Separator for Double LabelsDefine Minimum and Maximum Length Code 93 see Code 128 seeMSI / Plessey Code No Send Check Digit Double Module Label Code IV and V see Code 11 Special seeCodabar see No Send Exit EAN-8 EAN-13 see Supplement Code see Off / OnDelta Distance Code see Qualifiers Special Characters Modifiers Code Type Formula FormatSpecial Characters in this section TCP/IP Function Codes for PC Characters in parentheses represent Extended Code Ascii Chart = %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Generic Scanner Troubleshooting Tips Troubleshooting Problems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char