Terminator, Enter, Define Code ID | Unitech MS860 guide

PROGRAMMING VIA SCANNER INPUT

Scanner Port

Enter Group 5

0

1

2

3

Group Default

Terminator:

(see page 44)

0 - Enter

1 - Return (on keypad)D1

2 - Field Exit or Right Ctrl

3 - None

Code ID:

(see page 45)

0 - Disable

1 - EnableD2 Note: This setting does not affect EAN 128 Code ID. EAN 128 has its own Code ID setting (see page 51).

4

																				Define Code ID:
																				(see page 45)
																				00	- Code 39 Full ASCII
5																				00	- Code 39 Full ASCII				D3
5							01														- Code 39 Standard				D3
							01														- Code 39 Standard	11 - MSI Code
																				02	- EAN-13
																				02	- EAN-13
																				03	- UPC-A	12	- EAN 128
																				04	- EAN-8	13	- Code 32
6																				04	- EAN-8	13	- Code 32
6							05														- UPC-E		(Italian Pharmacy)
																				06	- Interleaved 2 of 5	14	- Delta Code
																				06	- Interleaved 2 of 5	14	- Delta Code
																				07	- Codabar	15	- Label Code
																				08	- Code 128	16	- Plessey Code
7							09														- Code 93	17	- Code 11 (Special)
																				10	- Standard 2 of 5 18 - China Postal Code
																							(Toshiba Code)

8


9																									Exit
67																						MS860 WiFi Manual

Image 69

Unitech MS860 manual Terminator, Enter, Define Code ID

Contents

MS860 WiFi Bar Code Scanner Table of Contents Introduction Introduction Quick Start Important Notes Importantscanner Ndotesaccessories Scanner LED Scanner Parts Buzzer Cradle LEDs Cradle Parts Charging the Scanner How to determine if the scanner needs recharging Network Settings Modifying the WiFi settings IP Address Glossary WEP Using SCM for Scanner Network Setting Network Settings Network Settings Network Settings Network Settings Using BAR Codes to SET Scanner Network Example IP Space 192.168.1.250 CR Network Settings Example Default CR Installing Virtual COM Network Settings Start Virtual COM Network Settings Vcom should automatically create a virtual com port for Glossary ConfigureWEP the virtual com port using monitor.exe Keep the default settings of the server port and server IP Network Settings Network Settings Start It Up Scanner Configuration Manager Try It Interblock Delay Beeps and DelaysIntercharacter Delay Keyboard Wedge Caps-Lock Function CodeLanguage Use Numeric Keypad Parity Baud RateData Bit Handshaking BCC Character RS232Time Out Data Direction Terminator Scanner Port Double Verification Use Code ID Settings Function Code RS232 BCC Character Scanner Port EAN-13 Label Code IV or Label Type Scanning Mode Aiming Time for Long Range Engine Aim Function for Long Range EnginePreamble Postamble Code Bar Code Symbologies Interleaved 2 Standard 2 of 5 / Toshiba Code China Postal Code EAN MSI / Plessey Code UPC-A Codabar EAN-13 UPC-E Delta Code EAN-8 Label Code IV Supplement Code for UPC-E, ISBN, EAN-13 Data Editing QualifierModifier Scanner Configuration Manager Everything Else Formula Arrange Formulas Introduction Programming VIA Scanner Input Beep Quick Setup Bar Codes UPC-E Intercharacter Delay Interblock DelayBeep Tone see page 40 0 None Medium Keyboard Interface 9600 Baud RateParity None Data Direction for terminal wedge see Send to Host Second Enter TerminatorCode ID Define Code ID Double Verification Scanning ModeTrigger Label Type Ppoo Code 39 see Symbologies GroupCheck Digit Not Calculate Interleaved 2 of 5 ITF see Code 32 Italian Pharmacy see Standard 2 China Postal Code Toshiba CodeTelepen UCC/EAN 128 see Define the EAN 128 Fields Separator Define a Separator for Double LabelsDefine Minimum and Maximum Length MSI / Plessey Code Code 128 seeNo Send Check Digit Double Module Code 93 see Codabar see Code 11 Special seeNo Send Label Code IV and V see Exit EAN-8 EAN-13 see Supplement Code see Off / OnDelta Distance Code see Qualifiers Special Characters Modifiers Code Type Formula FormatSpecial Characters in this section TCP/IP Function Codes for PC Characters in parentheses represent Extended Code Ascii Chart = %H ~ %S Delete %T ? %J NUL %U @ %V \ %L `%W # /C $ /D + /K Programming VIA Scanner Input SP Space Specifications Mechanical Generic Scanner Troubleshooting Tips Troubleshooting Problems and Solutions Problem No output from scanner Troubleshooting BAR Code Test Chart BAR Code Test Char