Wayne-Dalton 5140 Parallel with door, Or door stop too tightly against face, Door, Sides equally

			Angle bolted to ceiling
	Rear Support Continued...	PERFORATED	member and parallel to
		ANGLE	door
Tools Needed:	supplied). Horizontal tracks must be level	(3) 5/16”
	and parallel with door.	NUTS	Horizontal
	NOTE: If perforated angle is installed		track
	over drywall, use 5/16” x 2” hex head lag
	screws.	(3) 5/16”
	Adjust weather seal (if necessary) and
	now permanently attach the weather	BOLTS		Angle
	seal or door stop to both door jambs and
	header. (They were temporarily attached		Vertical
	to the jambs in PREPARING The OPENING
				Angle
	on page 10.) Avoid pushing weather seal		Bolt must extend into
	or door stop too tightly against face of		the track to serve as
	door.		a roller stop
	NOTE: If an idrive® opener will be	Sound Framing Members
	installed, position horizontal tracks one
	hole above level when securing it to rear
	supports.
	Now, lift door and check it’s balance.		Perforated
	WARNING		ANGLE

Prior to winding or making		Perforated ANGLE - BOLTED
adjustments to the springs,		USING (2) 5/16” X 1-5/8” HEX HEAD
ensure you’re winding in the		LAG SCREWS TO CEILING MEMBER
proper direction as stated in		AND PARALLEL TO WIDTH OF DOOR.
the Installation Instructions.		Space lag screws no further
Otherwise, the spring fittings may
		than 24” apart.
release from spring if not wound
in the proper direction and could
result in severe or fatal injury.	HORIZONTAL	BOLT MUST EXTEND INTO THE TRACK
Adjust, if door lifts by itself (hard to pull
		TO SERVE AS A ROLLER STOP
down) or if door is difficult to lift (easy to	TRACK
pull down). Anytime spring adjustments		Sound Framing Members
are made you must loosen the lock nuts
and retighten both lock nuts afterwards.		PERFORATED ANGLE
To adjust spring(s), only add or remove 1/4
turn on the counter at a time. Adjust both
sides equally.		Perforated ANGLE -BOLTED USING
IMPORTANT: Do not add or remove
		(2) 5/16” X 1-5/8” HEX HEAD LAG
more than 1 spring turn from
		SCREWS TO CEILING Members
specified amount. If the door still
		AND PARALLEL TO WIDTH OF DOOR.
does not operate easily, lower
the door into the closed position,		Attach vertical perforated angle
UNWIND SPRING(S) TO ZERO, and		between the (2) 5/16” X 1-5/8”
recheck the following items:		HEX HEAD LAG SCREWS, securing
1.) Check the door for level.		perforated angle to ceiling
2.) Check the TorqueMaster® spring tube		members.
and flagangles for level and plumb.	HORIZONTAL	BOLT MUST EXTEND INTO THE TRACK
3.) Check the distance between the
	TRACK
flagangles - must be door width		TO SERVE AS A ROLLER STOP
plus 3-3/8” to 3-1/2”.		PERFORATED ANGLE
4.) Check the counterbalance cables
for equal tension - adjust if
necessary.
5.) Rewind the spring(s).		Weather
6.) Make sure door isn’t rubbing on
jambs.		seal
NOTE: As a safety feature, the right hand
end bracket cannot be disassembled
for service until the spring is completely
unwound and the counter cover reads		Jamb
zero.
After door installation is completed, refer
to the idrive® owner’s manual.	(3) 5/16” BOLTS	Permanently attached
	& NUTS
		Weather seal

30Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com