![](/images/new-backgrounds/1168125/168125373x1.webp)
PROBLEM SOLVINGERROR CODES
Code | Display Message |
| Procedure |
|
|
| |
Incomplete paper width measure- | The paper width was set manually but LOAD was not pressed on | ||
| ment | the autoload panel. | |
|
| 1. | Press LOAD on the autoload panel. |
|
| 2. | Press RESET on the touch screen and then set the printer to |
|
|
| ready. |
|
|
|
|
Back tension cover open | 1. | Close the back tension cover of the printer. | |
|
| 2. | Press RESET on the touch screen and then set the printer to |
|
|
| ready. |
|
|
|
|
Hopper bar not set/Seam detected | 1. | Raise the hopper cover. | |
| (during autoloading) | 2. | Change the position of the hopper bar lever, on the left side of |
|
|
| the hopper. |
|
| 3. | Lower the hopper cover. |
|
| 4. | Press RESET on the touch screen and then set the printer to |
|
|
| ready. |
|
|
|
|
Hopper cover open | 1. | Close the hopper cover. | |
|
| 2. | Press RESET on the touch screen and then set the printer to |
|
|
| ready. |
|
|
|
|
Autoload | 1. | Press RESET on the touch screen. | |
|
| 2. | Remove the paper jam (see "Clearing paper jams" on page 9- |
|
|
| 3). |
|
| 3. | Restart the autoload procedure (see "Paper autoloading" on |
|
|
| page |
|
| 4. | Press LOAD on the autoload panel. |
|
|
| |
Pinch roller pressure motor A alarm | An overcurrent was detected in pinch roller pressure motor A. | ||
|
| 1. | Check the printing status and the paper position. |
|
| 2. | Press RESET on the touch screen and then set the printer to |
|
|
| ready. |
|
|
| |
Pinch roller pressure motor B alarm | An overcurrent was detected in pinch roller pressure motor B. | ||
|
| 1. | Check the printing status and the paper position. |
|
| 2. | Press RESET on the touch screen and then set the printer to |
|
|
| ready. |
|
|
| |
Pinch roller pressure motor A time- | An operation failure was detected in pinch roller pressure motor A. | ||
| out | 1. | Check the printing status and the paper position. |
|
| 2. | Press RESET on the touch screen and then set he printer to |
|
|
| ready. |
|
|
| |
Pinch roller pressure motor B time- | An operation failure was detected in pinch roller pressure motor B. | ||
| out | 1. | Check the printing status and the paper position. |
|
| 2. | Press RESET on the touch screen and then set he printer to |
|
|
| ready. |
|
|
| |
Pinch roller A position error | Pinch roller A was in the up position during printing. | ||
|
| 1. | Check the printing status and the paper position. |
|
| 2. | Press RESET on the touch screen and then set he printer to |
|
|
| ready. |
|
|
| |
Pinch roller B position error | Pinch roller B was in the up position during printing. | ||
|
| 1. | Check the printing status and the paper position. |
|
| 2. | Press RESET on the touch screen and then set the printer to |
|
|
| ready. |
|
|
|
|
|
|
|
Xerox 495 Continuous Feed Duplex Printer Operator Guide | Page |