114, After Auto Setup, 2OVER 24m 80ft | Yamaha HTR-5990 specs

TROUBLESHOOTING

After AUTO SETUP

	Warning message	Cause	Remedy	See
	Warning message	Cause	Remedy	page
				page

		Speaker polarity is not correct. This
	W-1:OUT OF PHASE	message may appear depending on the	Check the speaker connections for proper polarity	13
	W-1:OUT OF PHASE	speakers even when the speakers are	(+ or –).	13
		speakers even when the speakers are	(+ or –).
		connected correctly.

	W-2:OVER 24m (80ft)	The distance between the speaker and the	Bring the speaker closer to the listening position.	—
	W-2:OVER 24m (80ft)	listening position is over 24 m (80 ft).	Bring the speaker closer to the listening position.	—
		listening position is over 24 m (80 ft).

			Readjust the speaker installation so that all speakers	—
			are set in locations with similar conditions.	—
			are set in locations with similar conditions.
		The difference of volume level among
	W-3:LEVEL ERROR	The difference of volume level among	Check the speaker connections.	13
		speakers is excessive. (No level correction	Check the speaker connections.	13
		speakers is excessive. (No level correction
		is made.)	Use speakers of similar quality.	—
			Use speakers of similar quality.	—

			Adjust the output volume of the subwoofer.	31

Notes

•If the ERROR or WARNING screens appears, check the cause of the problem, then perform the AUTO SETUP procedure again.

•If warning W-1 appears, corrections are made, but they may not be optimal.

•If warning W-2 or W-3 appears, no corrections are made.

•If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center.

■ HDMI

	Error message	Cause	Remedy	See
	Error message	Cause	Remedy	page
				page

	DEVICE OVER	More than 5 HDMI components including	Reduce the number of the connected HDMI	—
	DEVICE OVER	this unit are connected.	components.	—
		this unit are connected.	components.

	HDCP ERROR	HDCP testing failed.	Check that the connected HDMI components support	—
	HDCP ERROR	HDCP testing failed.	the HDCP copy protection standards.	—
			the HDCP copy protection standards.

114

Image 118

Yamaha HTR-5990 owner manual 114, After Auto Setup, 2OVER 24m 80ft

Contents

HTR-5990 Important Safety Instructions FCC Information for US customers Example of Antenna Grounding Pour LES Consommateurs Canadiens IiiFor Canadian Customers Serial No Contents Features Getting Started Supplied accessoriesPlease check that you received all of the following parts Remote control transmits a directional infrared ray Preparing the remote controlInstalling batteries Using the remote control Be sure to aim the remote control directly at the remote Controls and Functions Front panel FM/AM Tuning Mode AUTO/MAN’L, DisplayVolume Memory MAN’L/AUTO FM Return Remote controlLEVEL, Band Macro ON/OFF Standby PowerVolume + Audio SEL Front panel display Presence and surround back speaker indicators 96/24 indicatorLFE indicator Night indicator Wrench Holder Rear panelAC Outlets Before connecting speakers Connections Connecting to the speaker terminals Connecting speakersDi-pole speaker layout Speaker terminal wrench Red positive + Black negative 10 mm 3/8Red positive + Black negative PRESENCE/ZONE 23 terminals Connecting the banana plugSpeaker layout Connect presence speakers to these terminals Right Left Surround speakers Surround back speakers Conventional connection Using bi-wire and bi-AMP connectionsBi-wire connection Bi-AMP connection Analog jacks Cable indicationsDigital jacks Audio jacks Digital Audio Optical jacks Audio signal flow for OUT RECAudio jacks Digital Audio Coaxial jacks Video jacks Video signal flow for Monitor OUTVideo jacks Component Video jacks Hdmi out DVD Player Cable TV or Connecting Hdmi componentsHdmi Video Monitor Connecting a DVD player Connecting video componentsVideo Monitor Satellite tuner Connecting other video componentsDVD recorder Or VCR Connecting to the Multi CH Input jacks Connecting to the Video AUX jacks on the front panel MD recorder or tape deck Connecting audio componentsCD recorder CD player Connecting an external amplifier Ground GND terminal Connecting the antennasConnecting the AM loop antenna Indoor FM antenna included Turning on and off this unit Connecting the power cableConnecting the AC power cable Memory back-up This unit will be set to the standby mode Setting the speaker impedanceSelect 6 ohms if you are using 6 ohm speakers This unit, Zone 2 and Zone 3 are turned off Optimizer microphone setup Auto SetupIntroduction SET Menu Using Auto SetupPress n to select Setup and then press l / h to select Auto Resultexit AutomenuIf you selected Auto in step Press Enter to return to the Resultexit screen If you selected Reload in stepResultexit display appears Press Enter to confirm your selection Press Speakers a or B on the front panel PlaybackBasic operations Or press Speakers a or B on the remote Dial Norm Front panel Remote control Name of the sound field categoryProgram name Press Mute on the remote control Adjusting the tonal qualityUsing Silent Cinema Additional operations Enjoying multi-channel software 7.1 channel surround To play back Dolby Digital or DTS signals in 5.1 channelsSelecting the Multi CH Input Auto Enjoying 2-channel software in surround Press Select on the remote control to select a decoderDecoder types for the Surround program Choices MIN, MID, MAX Using Pure DirectUsing the night listening modes Lights up Downmixing to 2 channels Using the sleep timerListening to unprocessed input signals Straight Playing video sources Background Virtual Cinema DSPSelecting audio input modes Audio information Displaying information about the input SourceVideo information See page 28 for details Turn on the power of this unit and all connected componentsRecording Front panel or Press PRESET/TUNING/CH l / h once to begin automatic tuning FM/AM TuningAutomatic tuning 4 1 Manual tuning Automatic preset tuning Customized automatic preset tuning Memory indicator flashes for about 5 seconds Manual preset tuningSee page 44 for tuning instructions 2,5 Selecting preset stations Repeat steps 1 to 5 to store other stations Press PRESET/TUNING Edit again Exchanging preset stationsPress and hold PRESET/TUNING Edit for more than 3 seconds 1,3 1,3 XM Satellite Radio connections XM Satellite Radio TuningWhat is XM Satellite Radio? Information from XM Satellite Radio Inc Front panel functions Remote control functions XM Satellite Radio controls and functions Activating XM Satellite Radio Press PRESET/TUNING/CH l / h orPRESET/CH k / n on the remote control to Select channel Using XM Satellite Radio search modes Selecting the XM Satellite Radio modeAll Channel Search mode Category Search mode CAT Search Direct Number Access mode Preset Search modePreset Search When the channel number 040 is selected Setting XM Satellite Radio preset channelsDisplay changes as follows Group letter appears Preset groupPreset number Colon appears Displaying the XM Satellite Radio information Displaying the XM Satellite Radio information in the OSD Editing Sound Field Parameters What is a sound field?Changing parameter settings Elements of a sound field Resetting parameters to the factory values Source Control Sound Field Program DescriptionsFor movie/video sources Program THX For music sources 7ch Stereo DSP Level DSP level INIT. DLY / P. INIT. DLY Initial delaySound Field Parameter Descriptions Room Size / P. Room Size Room size Liveness Liveness INIT. DLY Surround initial delaySB. INIT. DLY Surround back initial delay Room Size Surround room size REV. Time Reverberation time REV. Delay Reverberation delayREV. Level Reverberation level For PL x Music Dialog Lift Dialog liftFor 7ch Stereo For Neo6 Music For Surround Standard Decode Type Decoder type For Movie TheaterFor THX Cinema For Surround Enhanced Channel audio 6.1-channel Sound Field Program Speaker LayoutsStereo Audio Audio *3 Monaural Stereo Audio *1 Audio *2 Standard Straight Manual Setup Use to manually adjust basic system parameters Use to manually adjust the optional system settings Option Menu Using Manual Setup Use the remote control to access and adjust each parameter Front SP Using Basic MenuLFE/BASS OUT Center SP Presence SP Subwoofer PhaseSB L/R SP Cross Over Speaker level BSP Level BSP LevelCSP Distance Speaker distance CSP Distance Etest Tone Using Sound MenuDthx SET Aequalizer Ehdmi SET Blfe LevelDaudio SET Cdynamic Range Using Input Menu Multi CH Setup Emulti CH SET Ddecoder ModeCvolume Trim Binput Rename Using Option Menu Adisplay SET Caudio Select Bmemory GuardHdmi interlace/progressive up-conversion Fzone SET EPARAM. INIParameter initialization EPARAM. INI Zone 3 amplifier ZONE3 AMP GXM Radio SETXM Satellite Radio set GXM Radio SET Display Display Selecting the OSD mode Adjusting speaker levels Advanced Operations User preset Preset Advanced SetupUsing Advanced Setup Name of the selected parameter Current setting Remote control tuner ID Remote TUN Wake on RS-232C access Wake on 232CRemote control AMP ID Remote AMP Remote control XM ID Remote XM Controlling this unit Remote Control FeaturesControl area Controlling other components Controlling each component VOL Set AMP/SOURCE/TV to Source Setting remote control codesRemote Control Code Default Settings Input area Component Code Category Setting remote control XM codes Setting remote control AMP codesSetting remote control tuner codes Press Enter Press an input selector button to select a source component Using LearnPress Learn again to exit from the setup mode A. model To 10 cm 2 to 4 Press Learn again to exit the learning mode Press Learn using a ballpoint pen or similar objectLearn appears in the display window Using RE-NAME Press a macro button Using MacroMacro buttons First Second Third Programming Macro operations Press Macro using a ballpoint pen or similar objectMacro operations Set Macro ON/OFF to on Press a macro button Press k / n to select the clear mode Using ClearPress Clear by using a ballpoint pen or similar object Basic Clear operations Clearing a learned function Remote control returns to the learning mode100 Press Learn again to exit 101 Press Clear to exit the clearing modeRemote control returns to the macro programming mode Clearing a macro function Zone 2/ZONE Connecting the Zone 2 and Zone 3 componentsUsing the external amplifiers 102 103 Using the internal amplifiers of this unitSelecting Zone 2 or Zone Front panel operations Controlling Zone 2 and Zone Remote control operationsSet AMP/SOURCE/TV on the remote control to AMP 104 Adjusting the tonal quality of Zone 2 or Using the control mode of Zone 2 and ZoneAdjusting the volume level of Zone 2 or 105 106 What is HDMI?Hdmi Hdmi compatibility with this unit Basic Hdmi operations Setting the Hdmi parameters107 108 TroubleshootingGeneral 109 110 Tuner 111XM Satellite Radio Remote control 112 113 Before Auto SetupDuring Auto Setup Connect MIC 114 After Auto Setup2OVER 24m 80ft Audio information Glossary115 PCM Linear PCM 116Neo6 Sampling frequency and number Quantized bits Sound field program information Video information117 Gain 118Frequency Factor Specifications 119 DVD Player CableCD Recorder DVD Recorder Tape Deck Satellite Tuner Contec VCR WF99950